Jump to content
SAU Community

Recommended Posts

what a spew hey, hope you sort it out. chasers have a stock item im pretty sure.

u could just put a muffler on it to shut it up and quieten it down or a resonator

i wouldnt goto the effort to change dump/cat/full system etc to pass epa test

unless you really had to of course

krzysiu,

Have you taken it to an exhaust shop to get it tested yet?

I got the same letter, took my car to get it tested and it was spot on 90 dB, therefore legal....

I thought mine would fail dismally but it passed.... Get it checked for $25 bucks and then you get a document saying its right and you can keep it in the glovebox to say that the exhuast is inside regulations.

BASS OUT

krzysiu,

Have you taken it to an exhaust shop to get it tested yet?

I got the same letter, took my car to get it tested and it was spot on 90 dB, therefore legal....

I thought mine would fail dismally but it passed....  Get it checked for $25 bucks and then you get a document saying its right and you can keep it in the glovebox to say that the exhuast is inside regulations.

BASS OUT

Hey Bass, I got the EPA letter and it saye this on the bottom:

NOTE FEE INCREASE

The approved noise tester will charge the following

for a noise test

From 9 May 2005 - $33.75 (including GST)

From 1 July 2005 - $34.60 (including GST)

Can you also tell me the size of your exaust because i will get annoyed if i pay 35 bucks and i fail, then i have to do it again = 70bucks :) Not that much but its still some money that cat be better spent on a saturday night ;)

cheers

I have a Fujistubo Power Getter high high flow cat and Blitz front pipe, stock dump pipe.

Go to the exhaust shop, tell them you got the notice, ask them to listen to your exhuast, they will know soon enough whether it is over or not.

I have a Fujistubo Power Getter high high flow cat and Blitz front pipe, stock dump pipe.

Go to the exhaust shop, tell them you got the notice, ask them to listen to your exhuast, they will know soon enough whether it is over or not.

Ah ok, bad thing is i got some Big Jap Spec Dump pipe, and a full stainless steel 3.5 inch Turbo back Blitz system.

Thanks for the advice, ill just take it and let them have a listen.

i had the same thing with mine, was too loud so all i did was get a smaller muffler on the rear for the check, when i got home just put the cannon back on :)

this is very simple dude, and if u know that u r only a few dB's over then fill it with chicken wire

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...