Jump to content
SAU Community

Recommended Posts

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Do i get a cookie  :Pimp2:

:cookie:

tommyk I don't see why not:

the highest peak was 253kw but we settled on the 247 as it made more midrange than the 253 setting.

dyno_graph_-_247vs221p.JPG

COOL

What mods do you have and was that run done in awd or rwd mode ?

You guys suck. You make me want to buy a pair of GT-SS's :D

as for mods mine is still stock turbos, stock cams, stock intercooler, stock dumps, stock front pipes. just 3 inch cat back system, apexi pods, cam gears, 14.5psi boost, and power FC. obviously have other unrelated stuff like oil cooler, twin plate clutch, OS gearset etc etc. the first graph showing 221kw was before the cam gear adjustment. in the process of adjusting the gears boost also rose by 2psi (without touching the controller) and the AFRs leaned off a bit (also without touching the PFC). so that may have influenced the gain a little too.

is that graph rwkw or awkw ?

Why do I ask ?

Ive got everything you have including 15psi boost, aftermarket front pipes, but i dont have the pods or gears

Sorry for the hijack kabab

sorry mate, it's in rwd. so outright power i would say it's pretty much the same between us (i don't know really) but the shape of the curve is what is most important to me at the moment, not the peak figure. :D

sorry mate, it's in rwd. so outright power i would say it's pretty much the same between us (i don't know really) but the shape of the curve is what is most important to me at the moment, not the peak figure. :D

I noticed when mine was on the dyno it was in full 4wd mode so i guess thats why your figure is much higher then Tommyk's..

What would the difference be between awd and rwd power wise?

to be honest i really don't know. i have heard lots of stories. some people say on a 32 GTR the difference is negligible (something about the way they divert torque to the front wheels on a dyno), other say about 30kws difference. personally i think there must be some difference but how much i wouldn't want to guess.

Suffice to say that, as always, a dyno is not the best dick measuring tool as everyone has a different ruler.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...