Jump to content
SAU Community

Recommended Posts

^^ pretty sure you'll find that the S1 had drivers side airbags most likely as factory option.. most have them, however the S2 had dual airbags in every car..

Makes it an issue for compliancing as you need to fit an airbag to the car if it came with it factory I do believe..

If it doesn't have one now.. not much you can do short of paying a couple of $'000 to get one installed.. that is if you want it.. personally i wouldn't get a car without dual airbags.. but that's just me.

Link to comment
https://www.sau.com.au/forums/topic/78578-airbags/#findComment-1434170
Share on other sites

Have you tried just looking at a number of '95 cars forsale on websites, would be a good idea of knowing what came with what.. if all of them have an Airbag, than yeah, could be a problem.. if a fair few don't than i'd say it was still a factory option than.

However - all SII definately have dual airbags.

can you explain what the issue is? if it has been complianced without an Airbag and has a compliance plate than you should be fine to get it registered unless the RTA do an inspection and find something wrong. In which case, take it back to the compliancers and get them to fix it for you.

or

are you worried about your safety and after a car with an Airbag? very valid..

Link to comment
https://www.sau.com.au/forums/topic/78578-airbags/#findComment-1439243
Share on other sites

Issue? I dont want to get defected and have to spend shitloads on a new steering wheel... thats pretty much it. Nah havent looked at others for sale thanks for the idea. I'll check the compliance plate too. Nah the safety wasnt too much thought about. Probably should think about it tho lol

Link to comment
https://www.sau.com.au/forums/topic/78578-airbags/#findComment-1439377
Share on other sites

Mate, my car is a 1995 series 1.5 its ment to have an airbag. It had an aftermarket wheel which was taken off before i purchased it, so i replaced it with just a series 1 steering wheel. It has been over the RTA, and nothing was said about it.

I've seen 96+ skylines with sports steering wheels, and it didnt matter either.

To tell you the truth, the RTA doesnt really know if theyre ment to have them or not, they didnt have a check sheet there to tick off, so if it was rego'd like that, as far as your concerned, it never had one to begin with, nor am i.

Hope this helps.

Dayne

Link to comment
https://www.sau.com.au/forums/topic/78578-airbags/#findComment-1439467
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...