Jump to content
SAU Community

Recommended Posts

hey

buy a r32 type M and im susing out teh brakes to make sure there the right size.

wat are teh sizes for the Type M im pretty sure they are teh GTR brakes, and im sure they are 4 pot front 2 at rear. i know the type M come wit gtr rims and stearing wheel. i just want the actuall measurements of teh Type M brakes

:confused:

Link to comment
https://www.sau.com.au/forums/topic/78613-r32-gts-t-type-m-brakes/
Share on other sites

Hi there,

Good luck on finding your information - it's all here already however as this topic has been covered before. Try searching for it and you should be able to dig up the info you're after.

You should really learn how to spell and form sentences properly and you'll get more response too.

:)

Cant really understand what your asking for, but the type M does have 4 pot front and 2 pot rear brakes, but they arent the same as the GTR ones.

The type m does not come with GTR wheels or steering wheel.

R32 GTSt type M rotors are 280mm x 30mm thick

R32 GTR rotors are 296mmx32mm thick

R32 GTR rims look similar but aren't the same as type M as they are wider and forged alloy

where the type M are cast alloy.

The steering wheels are similar too but the GTR has a different horn button.

R32 GTSt  type M rotors are 280mm x 30mm thick 

R32 GTR rotors are 296mmx32mm thick

R32 GTR rims look similar but aren't the same as type M as they are wider and forged alloy

where the type M are cast alloy.

The steering wheels are similar too but the GTR has a different horn button.

Boo yaaa... told you I was right..

Yeah they are more rare, but are a lot more common now due to the 15 year rule. Back when compliance was $3000 for r32 gtst's, there probably wasnt much point in bringing in non-type-m r32s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...