Jump to content
SAU Community

Recommended Posts

hey

buy a r32 type M and im susing out teh brakes to make sure there the right size.

wat are teh sizes for the Type M im pretty sure they are teh GTR brakes, and im sure they are 4 pot front 2 at rear. i know the type M come wit gtr rims and stearing wheel. i just want the actuall measurements of teh Type M brakes

:confused:

Link to comment
https://www.sau.com.au/forums/topic/78613-r32-gts-t-type-m-brakes/
Share on other sites

Hi there,

Good luck on finding your information - it's all here already however as this topic has been covered before. Try searching for it and you should be able to dig up the info you're after.

You should really learn how to spell and form sentences properly and you'll get more response too.

:)

Cant really understand what your asking for, but the type M does have 4 pot front and 2 pot rear brakes, but they arent the same as the GTR ones.

The type m does not come with GTR wheels or steering wheel.

R32 GTSt type M rotors are 280mm x 30mm thick

R32 GTR rotors are 296mmx32mm thick

R32 GTR rims look similar but aren't the same as type M as they are wider and forged alloy

where the type M are cast alloy.

The steering wheels are similar too but the GTR has a different horn button.

R32 GTSt  type M rotors are 280mm x 30mm thick 

R32 GTR rotors are 296mmx32mm thick

R32 GTR rims look similar but aren't the same as type M as they are wider and forged alloy

where the type M are cast alloy.

The steering wheels are similar too but the GTR has a different horn button.

Boo yaaa... told you I was right..

Yeah they are more rare, but are a lot more common now due to the 15 year rule. Back when compliance was $3000 for r32 gtst's, there probably wasnt much point in bringing in non-type-m r32s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...