Jump to content
SAU Community

GCG Hiflow Hybrid on R33 GTS-t

Bullant47
 Share

Recommended Posts

  • Replies 316
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Cubes Grand Master

Cubes

Posted
Posted

Basically the new gen core is rated to flow more, the older core is rated to flow less.

If it's possible to use the new gen core with the internal gate housing i'm not sure, if it works well is another thing, you may experience surge with a small exhaust a/r?

Bass Junky Grand Master

Bass Junky

Posted
Posted

Bullant.

You mentioned the GCG may bring back the 500 hp turbo, but woulld have to address the size of the wastegate in order to make it commercially viable.

Did they offer to enlarge your wastegate?

I once spoke to them about highflowing my turbo and I asked if they could make it bigger, and they said no problems.

Just a thought.

Any further reflections on how the turbo performs?

Have you done the 2nd gear from walking pace test? When does she begin to boost?

BASS OUT (Still searching for a VG30DET Exhaust housing)

Bullant47 Community Regular

Bullant47

Posted
  • Author
Posted

Sorry i dont know about a 500hp hi flow.

2nd gear boost starts at about 2200rpm and makes a lot of wheel spin at about 3700rpm.

3rd gear boost starts at about 2200rpm and makes full boost (19psi) at around 3800rpm.

It ramps up very strong and really fast in between these revs.

Munna Rising Star

Munna

Posted
Posted
Sorry i dont know about a 500hp hi flow.

2nd gear boost starts at about 2200rpm and makes a lot of wheel spin at about 3700rpm.

3rd gear boost starts at about 2200rpm and makes full boost (19psi) at around 3800rpm.

It ramps up very strong and really fast in between these revs.

I did the same thing in my car as have a standard turbo for a comparison (mods are in sig). I did it by just idling along in the selected gear than just held it flat.

2nd gear boost starts at 1000rpm and full boost 11psi at 3000rpm.

3rd gear was exacly the same.

So to me it looks as though boost comes on 1000rpm later but spools just as quick or quicker than stock. You have got to be happy with that very impressive. I would like to see people do the same tests with 2535 standard gcg highflow ect for interests sake.

:D

Cubes Grand Master

Cubes

Posted
Posted
Bullant.

 

You mentioned the GCG may bring back the 500 hp turbo, but woulld have to address the size of the wastegate in order to make it commercially viable.

 

 Did they offer to enlarge your wastegate?

The issue with the old GCG 500hp highflow wasn't boost creep (where boost cannot be kept down, creeps up as revs increase) the issue was with surge.

A larger exhaust a/r was needed to help shift the full spool a little higher in the rev range where the motor can consume the air better.

I'm unsure of the differences between the 500hp and 450hp highflows they offered, I assume it was the compressor size.

It looks as if the GCG Highflow on the rb25 would be very similiar to the XR6 Turbo on the Rb30. Spool wise. :D

Cubes Grand Master

Cubes

Posted
Posted

I did it in mine today. Stock Rb20DET Turbo running stock boost. :D

Boost and surge under 2000rpm, as soon as 2000rpm hits it kicks and breaks in to a wheel spin at this time it looks like its wheelspinning around 2300rpm or so. :)

Just a pitty the power drops off rapidly after 5000rpm and peak power is made around 4400rpm. lol

discopotato03 Grand Master

discopotato03

Posted
Posted

Cubes yes , the GT30 housings will fit early and late cartridges as will any housing machined (profiled) to suit .

Garrett often sells cartridges without exhaust housings so the end user can select one of several to suit his/her application . If you look in the old Garrett catalogue PDF the "GT3071R" (700177-23 CHRA No) is sold as a cartridge without compressor or exhaust housings but there are three variations of both turbine and compressor housings available .

The integral gate HKS housings are the go and while expensive not as much as an aftermarket cast manifold and waste gate . GCG can get HKS housings (as I suppose HPIAB could) and if enough people were interested they could possibly market these with late "GT30R" turbochargers that will bolt up and take advantage of all the available technology .

Cheers A .

Bullant47 Community Regular

Bullant47

Posted
  • Author
Posted
Got any pics?

No sorry, I only had the VG30 in my possession for about 15 minuites. GCG got it and opperated on it almost immediately...It was complete with dump, 02 sensor and in good condition actually.

Hey on another note, I went back to C&V for a touch up on the tune cause along with the massive power the car is making, some knock was occasionally observed on the Power FC. It appears that the R34 fuel pump is maxed out and A/F is leaning out at high speed (around 180kph). Next week a Bosch 044 and swirl pot is being fitted to keep the A/F line straight on the graph. Con recons the turbo is so efficient that with more fuel he can make a lot more power safely. After he played with the high end fuelling and took out a little timing it actually made 273.9kw@tw. 3kw more than before. So be prepared to think about fuelling cause the GCG Hiflow with the VG30 turbine housing sees the end of the GTR fuel pump upgrade. I'll post up the dyno sheet when i hook up the scanner.

Ian

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...