Jump to content
SAU Community

Recommended Posts

Hi all,

I am looking at an JUN oil pump for use in an R33 GTR and have read that JUN also recommends using their crank/oil pump collar in conjunction with this pump on "earlier" GTR's.

Can anyone confirm if the JUN pump can be used on its own or if the additional purchase of the matching collar is essential for fitting in an R33?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/79168-jun-oil-pump-upgrade-on-r33-gtr/
Share on other sites

Nick, the collar is needed to extend the drive flats for the oil pump in early RB26 engines (R32 I believe this is limited to). I've seen the wear marks on the pump drive and understand the concerns. Yours should be good.

Remember the RB26 is pretty much a complete engine out to do the oil pump. What else are you planning? ;)

Why change the pump? are you having pressure problems?

Thanks Geoff ;)

Just preparing my shopping list so to speak :( When the time comes the JUN or Trust pumps look to be the preferred option rather than an N1.

I did notice Trust rate their oil pump only marginally higher than the JUN equivilent

I wouldnt mind hearing from someone who is running the Trust pump as well

I bought a pump that was only used for mock up of the engine from a guy, but when I received it (all the way from Japan) the rear cover has GREX on it.

I'm assuming this is made by the same mold because I took it apart and compared it to another pump that had JUN on the back cover.

Is there one main Co. making these uprated pumps, then sourcing them out for re badging?

Is my pump with GREX really a Greddy or Trust pump??

PLEASE ADVISE

thanks

joel

Trust and Jun use a modified Nissan oilpump casting, where the HKS/Nismo have the same aftermarket casting. I think they are the same pump, or are made by the same foundry? The Tomei one features the largest oilpump gears in the universe, again in a custom case. All of them use their own oilpump gears, with wider, larger teef. Also features the pressure relief outside the case, so you can adjust the pressure externally without taking the car to pieces. Although there are other aftermarket devices you can adapt to do that without paying through the nose for a Tomei pump.

Although you pay for the difference, I think GTR-700 has shown the Jun pump capable of decent longevity and flow, so I'm not sure it's necessary to go further.

0042_01lo.jpg This one has the fitting welded to the pump....

This is why I like the Trust oil pump over the regular castings of the oem and N-1 pump.

I'm making up a external pick up into a custom alum oil pan to go on my rb26 powered Z car.

The standard casting oil pump does not provide enough "meat" for a tapped fitting to be used. The custom pan is needed for the rear sump placement in the Zed....

Oil_pump_side_feed_mod.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...