Jump to content
SAU Community

RB26DETT exhaust port "bulge"?

LTSJayce
 Share

Recommended Posts

LTSJayce Veteran

LTSJayce

Posted
Posted

I was at a local workshop,and noticed a bare RB26DETT head. The exhaust ports each had a "bulge" that seemed to be factory cast( I haven't seen many heads actually bare and off an engine to notice this cating thing...). The extend a reasonable way back into the head,and I'd offer an opinion that they'd take up a reasonable bit of real estate in the port,flow wise. The front three cylinders' bulge was facing,I think, rear + lower in the port,with the rear three cylinders facing forward + lower. I've heard a theory that they protect a waterjacket,but I've also heard that workshops grind them down to improve exhaust gas flow...so,no waterjacket. Are they fine on a standard engine,but removed on bigger power-up jobs? Nissan wouldn't have put these bulges there because they were bored. So;what gives?

Link to comment
https://www.sau.com.au/forums/topic/79215-rb26dett-exhaust-port-bulge/
Share on other sites
LTSJayce Veteran

LTSJayce

Posted
  • Author
Posted
Its to help direct the flow in the stock manifold. :D

Remove it if you are planning on using a nice tubular manifold.

In reality there is bugger all in it.

Thanks,Cubes! I hoped that was the idea. I have a really nice set of HKS extractors(the ones whose model escapes me-they have the "balancer" tubes between the front and rear three cylinders)that will most likely benefit from said removal ,and subsequent matching,when my head work gets done. If I was leaving the engine as standard,I wouldn't have touched these bulge things,but with what I have planned...well,it looks like they'll probably have to go! Thanks too for the more learned of my fellow SAU'ers that've kept an eye on my inexperience via this thread and helped accordingly! Cheers guys! Jayce.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • PranK
      R35 GT-R production ends after 18 years

      By PranK · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...