Jump to content
SAU Community

Recommended Posts

HICAS is good at high speed along the freeway, but at low speeds and general cornering and flicking the ass out I'm finding that I just don't like how it behaves. Going on other people's comments that's not too uncommon. I wanna slide sideways damnit!

It's quite strange - very different to any other RWD i have driven and i think i've decided over the last few weeks i don't like and want to waste some more tyre :D

I did a bit of a search but not too much in terms of how to remove it. I jacked up the car the other day and found it was a lot more accessible than I thought, just sticking out there little motor behind the rear axle.

Now, can I simply pull out the elec. plugs and that will disable it or is it more complicated than that? I have seen separate HICAS lock kits - where abouts can i find these and are these essential?

For short term i'm happy to do a quick and dirty fix (and just remove elec connections) as long as it works. Longer term if I can do a proper solution and get a locking kit??

Thanx in advance

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

predator666,

If you go to the Whiteline website they have some info on HICAS bypass kits, and I believe are coming out with one of there own. For track use disabling the HICAS is a good idea, but for daily driving I would probably keep it. The bypass kits have tended to be quite expensive, so what you have done is a much cheaper option, but leaves you with the HICAS light on the dash.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-119857
Share on other sites

I'll remove the steering wheel and disconnect it in there - going on a previous post that is the best place to do it. Guess if starts acting too funny I'll connect it back up.

GTS-t VSPEC: true in some ways, but I just don't like the way it handles and it seems its fighting my ass end if if I'm doing corners sometimes the way I do (not all the time!). And in the wet well i'm a bit worried how it will react if i lose traction and it goes sideways. In my old car i knew precisely how to control it when that happened at it was me controlling that back end... in fact i used to do it a bit just for kicks to scare those behind me :D

I want do the bushes fairly soon to give increased traction as well or possibly set it up to try some drifting..not sure, will see.

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-119913
Share on other sites

Nissan Skyline R32 GTS-T, KYB Buzz Spec Shockers (Damper Adjustable)

huh? That is the 2nd one on the page?

I already have adjustable zeal coilovers for the springs - dampner and height adjustable. That should do for now in terms of that side of things.

btw: Its an R33 - sorry for not posting that b4.

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-120055
Share on other sites

Thought it might be that one. The R32 one is apparently hyraulic and the R33 is electronic.

Therefore with the R33 it should just be a matter of disabling the electronics. When i think about it though, unless it is actually locked it still might be a bit floaty.

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-120091
Share on other sites

Originally posted by predator666

Therefore with the R33 it should just be a matter of disabling the electronics. When i think about it though, unless it is actually locked it still might be a bit floaty.

Check out this link

http://homepages.tig.com.au/~robs/hicaslock.htm

Like you said, for the R33's it's a bit more complicated cause you have to fool the computer and lock the rack.

If you don't lock the rack, you end up with lots of toe in and when turning hard corners the wheels can actually push the fluid around !!!

I've got a Tomei HICAS lock in mine :( but I haven't driven any other R33's so I can't compare.

J

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-120196
Share on other sites

BTW the hicas is only active at speeds above approx 70-80kph, and even then only moves the wheels a max of 1 degree.

I have heard this, but its mainly taking a corner and trying to kick the ass out. It just "feels" funny when i'm doing it - like the ass end is all wobbly. Of course if the wheels are spinning too much wouldn't it think it was going 70-80km/hr and kick in the HICAS?? It could just be a need for stiffer bushes and stuff which i'll get fitted soon

See that is the thing - I don't really know what its doing and would prefer it just to handle like any other RWD which i've driven for years.

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-120201
Share on other sites

Originally posted by GTS-t VSPEC

Jay,

Thanks for the link, it sounds like the only real way to do it. I'll have to get the kit when I take it out on the circuit. Is it widly available in Aus?

See'ya :burnout:

No problems :(

I'm pretty sure it's available through UAS or JMS, or they can order it for you. Actually, it might be even cheaper though http://www.takakaira.com/

I was lucky cause my car had it in already when I bought it.

It was funny cause I only found out that it had it about 9 months after I bought it !!!!

J

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-120228
Share on other sites

Originally posted by CanberraR33

Is it true that if you replace the standard steering wheel on an R33 that then HICAS will be disabled?

When does HICAS activate? Is it constant or only above a certain speed?

I haven't had any experience with the Skyline, however the HICAS on the Zeds is pretty much the same.

The steering angle sensor is mounted in the steering column, so if you change the wheel it may not work properly, will most likely cause a fault code and then the HICAS will disable, similar thing will happen if the steering wheel is not fitted straight.

HICAS is active above approx. 60kph and takes inputs from speed, steering angle, throttle position etc. It's constantly moving the rear wheels to keep the car balanced.

I have some really good info on the HICAS which I can scan and post if anyones interested, explains it fully

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-122634
Share on other sites

all you need to do is unplug the motor to the hicas to eliminate it

crawl under the rear of your car and you will se the motor near the diff

unplug the wires(hicaslight comes on ) and hicas is disabled

you may think that it will move freely now,,,wrong the motor wont move at all its locked into position internaly untill its told to move

the lockout kits are expensive because they have a curcuit to fool the hicas computer into thinking its still working so you dont get the hicas light coming on thats all

Link to comment
https://www.sau.com.au/forums/topic/8292-removing-hicas/#findComment-122678
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...