Jump to content
SAU Community

R34 Gt-t Offset Question

Binky1970
 Share

Recommended Posts

satanic Grand Master

satanic

Posted
Posted

Hey Binky, sorry to interrupt with your quest for the offset... but is that a GTR front lip on your GTT? That is mounted to the standard bar right?

Where did you get it and for how much if you don't mind me asking...

Sorry to interrupt once again :P

Binky1970 Rising Star

Binky1970

Posted
  • Author
Posted
I don't know the wheels offsets exactly but I know that wheels that fitted an R33 will fit an R34 properly.  R32 are different.

what did the wheels you are looking at come off?

Haven't actually bought them yet, still not sure if they will fit.

http://www.skylinesaustralia.com/forums/in...showtopic=83837

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Meh, 18's suck!!

The Te37's on the GTR rub the arches front and rear, cost too much for rubber, have limited access to semi comp rubber and don't feel as good on the road. Too little tyre, too much wheel = harsh ride. They are also prone to understeer due to the amount of mass away from the centre of rotation.

I'd sell mine in a second for a decent set of 17's with enough cash adjustment.

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

I just had a look at the spare set of R34GTt wheels I have here and they are 225 from side to side on the tyre, so say 215, and 154 from back of tyre to mounting face so say 150. This would suggest 215/2=107 being halfway and 150-107=43. So about 40 offset.

The wheel markings are 17x7 1/2 JJ and another marking simply states 40 which could be the offset.

What the clearances are over the brakes I couldn't say.

n15m0 Grand Master

n15m0

Posted
Posted

+30 should fit fine. The standard GTT wheels are +40 and they sit way in the guards. +30 will see your wheels come out by another 10mm which is not a lot. I once tested a +22 wheel on my GTT and it pretty much sat flush on the guards. Just make sure they clear ur brakes :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • WMDC35
      Tomei gasket

      By WMDC35 · Posted

      Are you sure the gasket is blown? What are the issues? Thermocure is the only flush I've seen do anything with rust, very impressed with that, Prestone, rust will be by the pool having a cigarette.  
    • MBS206
      Tomei gasket

      By MBS206 · Posted

      And since the flush you have a blown head gasket? Have you lifted the head off yet?
    • GTSBoy
      Hr34 fuel pump not turning on

      By GTSBoy · Posted

      The answer is to get a hold of the wiring diagram, work out what voltage is supposed to be where, when, and then work out why it is not there, then. I can't speak to the HR34 stuff, because I have never paid any attention to the NAs. There is a possibility that the turbo diagram will help, but it could also be different - depending on whether there is an FPCM on the NAs.
    • Trinicandian
      Hr34 fuel pump not turning on

      By Trinicandian · Posted

      Hey guys. New here. I am having an issue with my hr34. The fuel pump isn't turning on. I removed it from the tank. Bench test it. Wasn't working. Order new one and installed it today. Still not turning on. Checked the relay. Relay has voltage on the contact side. I jumped it and it tuned the pump on. Which lead me to checked the coil voltage.  Turned on the ignition and had my meter across the coil and there wasn't any dc voltage. Had my meter lead on the positive and I used the frame ground and noticed there was 12 volts. Which lead me to believe the relay isn't getting a negative signal. I traced the wire ( black with pink strip).it goes back to the bottom on the steering and it gets lost into the harness.   I checked at the ecm and I can't seem to find that wire color.   My question if any one knows is. Can I not just run the negative through a ignition relay to turn on the fuel pump relay?. Or anyone ever had this issue and if so how did u go about fixing it.    
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      So many people don't notice it, as batteries decay slowly over time. Two big reasons people end up noticing and needing to replace batteries: 1) The cold weather. The cold not only makes it harder to turn the engine for a few reasons, but it also increases the batteries internal resistance. So this means you need MORE power to turn a colder engine, AND the battery has a lower limit on how much current it can provide. 2) Something gets modified/altered/added in the wiring, typically an aftermarket accessory, like a dash camera, or an alarm etc, and this adds a small amount extra onto the battery, and pushes it over the edge in its failing days. But if you hadn't have read this thread, and just pushed through, chances are you might have made it through this winter, just. But come next winter, it would have been kapoot. But the fact you changed it out now, means you've instantly noticed how much nicer it is for starting, and will be less worry for you that the engine won't start now.
×
×
  • Create New...