Jump to content
SAU Community

Recommended Posts

I have for sale a brand new 90mm Veislide cat-back exhaust for an r32/33/34 gtr. It is full titanium (the real deal here folks!!!) and weighs about 4kg's. Comes with VeilSide titanium teardrop muffler. It has never been used and is sitting at my uncles workshop collecting dust! Asking $2000.

This is a quality product and buyer will not be disappointed!

Call Nick on 0408 605 141 or email [email protected]

post-6662-1124434630.jpg

Link to comment
https://www.sau.com.au/forums/topic/84632-fs-veilside-titanium-exhaust/
Share on other sites

lucien, i have seen one of these in the flesh (at up garage in chiba) and they are awesome. it's one piece from the cat right back to the tip and is very, very light. I would have bought the one in chiba but as it's one piece it was too hard to carry/freight. I think they are jasam approved too.

lucien, i have seen one of these in the flesh (at up garage in chiba) and they are awesome. it's one piece from the cat right back to the tip and is very, very light. I would have bought the one in chiba but as it's one piece it was too hard to carry/freight. I think they are jasam approved too.

They are impressive, but they also don't appear to have a resonator which tends to indicate they aren't JASMA approved (and also accounts for their lightness). Unfortunately there is nothing on Vielside's website either, hence the question.

Not sure if it is jasma approved. Is that some sort of governing body?

Yes, its the Japanese body that governs exhaust loudness. JASMA approval is a good indication that the exhaust will be near-enough legal on our roads. Usually there is a little stamp on the exhaust, or something amongst the documentation.

Lucien.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...