Jump to content
SAU Community

Recommended Posts

just spewing coz its got absolutely NO midrange

the hks2530 is known for its midrange torque so there definately must be something causing your turbos not to start pulling and spinning the wheels as soon as you stab on the throttle.

sorry hud let me clarifiy you need to keep the restrictor as it reduces the size of the hole the air has to travel through which increase the pressure holding the wastegate(act) closed ( think about a garden hose when u put your thumb over the end) Ive read that by altering the size of the hole in the restrictor you can change how the turbo ramps up on boost ie make it spool slightly earlier or later( hpi mag did a build up on a jap spec s15 which they did this on) if your missing the restrictor entirely by using pretty blue hosing instead you may get the problem you have as there is not enough pressure holding the wastegate(act) closed

  • 4 months later...

damn so 1 bar @ 4,000rpm is resonsble..? i was looking at the hks line of turbos for my r32 (rb20) was thinking

- GT2835 pro S

- GT-RS

- GT2530 (KAI what the diff with KAI or not??)

was told GT-RS would be laggy get the 2835 pro and i guess there going to shit aswell so might be looking at 2530 now?? anyone have any ideas on what the other 2 would be like??

I remember reading in some post that the new 2530kai is rated higher than the old 2530 in terms of power...old 2530 was 320ps i think and the 2530kai is something like 350-360ps or something like that...try searching here...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...