Jump to content
SAU Community

Recommended Posts

just wondering is my malpassi rising rate fuel regulator hurting my injectors?

some ppl say yes some say no whats your thaughts

this is my way that i can be bothered changed changing the injectors on my rb20det and will this support 200+rwkw cause i am up at 183rwkw and everything seems fine just want a little more boost and a little more fuel???

Link to comment
https://www.sau.com.au/forums/topic/85197-are-fuel-regs-safe/
Share on other sites

just wondering is my malpassi rising rate fuel regulator hurting my injectors?

some ppl say yes some say no whats your thaughts

this is my way that i can be bothered changed changing the injectors on my rb20det and will this support 200+rwkw cause i am up at 183rwkw and everything seems fine just want a little more boost and a little more fuel???

Rising rate fuel pressure regulators are tricky to tune for at times, I prefer a linear rate adjustable fuel pressure regulator. Rising rate FPR's are usefull for the older ECU's that didn't have rich and retard mapping.

Nothing wrong with increasing the fuel pressure above standard, to sneak a little more flow out of the injectors. As long as the fuel pump can deliver the extra pressure and still maintain the flow rate. That's the difficult part, an example. You might increase the fuel pressure by 10% and achieve a 4% increase in fuel flow from the injectors. But because of the extra resistance (pressure) the fuel pump might actually flow 6% less fuel. So you can actually go backwards if the fuel pump is not up to it.

The other issue is the ability of the standard rubber hoses and hose clamps to hold the increased pressure. Split hoses and leaking clamps are not good for fuel and a hot engine bay.

:( cheers :(

Sydneykids is spot on and i would just be carefull as you adjust regulator, chances are you need a new pump as they offen drop off dramatically as pressure increases (not designed to run much higher pressure but they will go a bit)

I have managed good results out of my std r33 gtr fuel system but only because i retain std fuel pressure and when the other way by putting big injectors (namely 530rwhp out of std fuel system and have done so on a r34 aswell)but for safety sake they will be upgraded in time.

So if your only looking for a few exact psi fuel pressure it shouldn't be a problem if your fuel pump still has a bit more in it. But if your looking for quiet a bit i would bit looking at bigger injectors and ecu to control them correctly.

my advice is don't trust the malpassi regulator i know of a number of people who have had trouble with them. particularly the gauges they come with.

I have also seen the malpassi used on a number of big budget drag cars - so they cant be all bad.

I have also seen the malpassi used on a number of big budget drag cars - so they cant be all bad.

Right on. If you keep them away from heat they really arent too bad. That said I have a bracket coming off my plenum for my reg, and its fine, get stuck in traffic, open the bonnet, its holding pressure perfect.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...