Jump to content
SAU Community

Recommended Posts

hey all,

im presuming that some people on here like photography (myself included)?? well anyway, here is a thread to post your fav pics of anything. cars, flowers, girls, whatever. also a place to share tips and stuff and just talk about general photogrpahy things.

they have to be taken by you and yeah ill start

Link to comment
https://www.sau.com.au/forums/topic/85615-photo-thread/
Share on other sites

  • Replies 517
  • Created
  • Last Reply

Top Posters In This Topic

mines a caplio R1 4.1 mp

made by ricoh, and i got mine 2 weeks before the new model came out so i got it about 200 bux less than rrp

btw, i really like that second pic you posted of the lake thingy

Its actually the brisbane river, from my balcony at sunset. The first and the last ones were taken in stanthorpe about a month ago (see the frost!) and the third one was taken at cunninghams gap (on the way to stanthorpe).

I like your sunset photo, any time i've tried to get a good one it always comes out dull. Same as all might night time photos :D

Link to comment
https://www.sau.com.au/forums/topic/85615-photo-thread/#findComment-1549376
Share on other sites

I sometimes find myself getting bored, so I go and try & get cool night shots.... I kinda like these ones.....

Camera is a Canon PowerShot S50

First 2 photos are done with photostitch, seem to have come out ok (high res originals look pretty good)

Edited by Bluprint
Link to comment
https://www.sau.com.au/forums/topic/85615-photo-thread/#findComment-1549702
Share on other sites

Guest Mashrock

some photos i took down at the snow.

the other week.

the last two were off my mates varandah, i sat out there for about 2 hours watching the clouds roll in through the valley. if i had a decent camera that could take photos in low light i could have got some very good photos of it. the coulds looked pretty damn cool rolling in..

photos are resized also

post-15086-1125318380.jpg

post-15086-1125318458.jpg

post-15086-1125318537.jpg

post-15086-1125318582.jpg

Edited by Mashrock
Link to comment
https://www.sau.com.au/forums/topic/85615-photo-thread/#findComment-1551927
Share on other sites

Guest Mashrock
Mashrock I like the second one...

And ryman htf you afford a house like that  :P

yeah i like that too. shit i filled up 512meg card last time i was there.

so many snow photos.

but i needa a better camera!

here is another.. but i beleive this was from a few weeks before the last time..

hehe i go to the snow alot.

Link to comment
https://www.sau.com.au/forums/topic/85615-photo-thread/#findComment-1554166
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...