Jump to content
SAU Community

Recommended Posts

i have recently had an R32 imported and it has the general little problems that need to be fixed, as they do.

i was driving around last night doin about 60 in 3rd not accelerating or anything and the car just cut out. i put the pedal to the floor and the car would kick in and out jumpin all over the place, so i put the clutch in and revved it to the shit and it came back good.

drove around for about half an hour no probs but the it did it again in fourth.

only does it randomly and it has me worried. it has been doin it all day today.

need some help if anyone has had similar probs.

i tried a search but couldnt find anything.

all advice appreciated. thanks...

Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/
Share on other sites

i've heard a few stories about air-flow meters going bad... not sure if this is your problem, maybe it needs a service - plugs + oil + filters?

My R33 misses under power about once every 5 takeoff's, very occasional but the bloke at Tilbrook has told me it is almost certainly the airflow meter faulty. The other confirming factor for Mr Tilbrook was that i only get 260kms from a tank! Not Good!

Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/#findComment-1565302
Share on other sites

thanks for the reply guys.

well if he told you that 260kms out of a tank is a factor, well mine must be pretty shot because i drive resonably sensible and only get 320kms out of a tank...

might pick up a second hand one from the import guys i got the car off.

it was fully serviced when i got it imported. whatched them do it. got oil and fuel filters, iridium sparkies, all oils new pod etc...

thanks again i thought i was up for thousands...........

it really had me worried

Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/#findComment-1565706
Share on other sites

happened to me on my r33 and i kno how u feel blooody annoying. i changed my plugs, fuel pump/filter and then found it was jus my air flow meter lol. upgraded to z32 no more problems :D

the airflow meter you said to me worked 100% fine when selling, which u said u upgraded thinking you would get more power with a z32?

lucky i did not buy it off you. cant trust many people nowdays can you!

Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/#findComment-1568058
Share on other sites

i think i found the problem.

pulled my air filter off and my afm today to replace it with another one.

i looked at the afm inside on the sensor and it was covoered in this black stuff.

turns out it was the oil from the air filter. got a K&N pod filter, when i put it on u have to spray it with this oil stuff from a can. i think that this has sucked through and dirtied the afm. i put this other afm on and it hasnt played up as yet. kept the old on and am going to clean it and keep it as a spare.

does anyone no how to clean these. the link to this in the diy / faq section doesnt work...

thanks again guys that helped me with the problem.

Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/#findComment-1572559
Share on other sites

Use carbi clean or throttlebody cleaner. These have always worked well. Contact cleaner works fine but I think is a little more expensive. I have never known any MAF meter to cause an engine to stall while your foot is on the accel. Usually at idle they stall. Sounds to be more like a fuel or ignition fault.

Edited by 3LIT3 FORS3
Link to comment
https://www.sau.com.au/forums/topic/86375-car-cuts-out/#findComment-1575542
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...