Jump to content
SAU Community

Recommended Posts

Will you be getting in any of these seats that are fully blue along with the shipment of seats that are fully red? Will be interested as soon as I can get some dimensions for the seats.

  • Replies 175
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Will you be getting in any of these seats that are fully blue along with the shipment of seats that are fully red? Will be interested as soon as I can get some dimensions for the seats.

Hi mate, thanks for your enquiry. Unfortunately we dont have any all blue versions of the Bride style seats coming, only black with the blue centre (which are in stock now)

Dimensions below as posted on page 2

Hi guys, approximate dimensions of the seats are as follows:

Overall Height: Approx 90cm

Widest Point: Approx 53cm (shoulder to shoulder)

Internal width at rear of base: Approx 33cm (actual seating area)

Internal width at front of base: Approx 36cm

Note: We now have 5 sets of black with grey centre, 4 sets of black with red centre and 4 sets of black with blue centre remaining so get in quick to avoid missing out.

The black/red version is winder type, and the black/grey and black/blue versions are lever type

Cheers,

Steve

Cheers,

Steve

I'll take some measurements from my bride rail shortly and post them up and hopefully JJ can do a quick measurement on their seats ;)

JK

ok these measurements were taken from the centre of each hole.

Front left to front right 285 to 300mm

Front left to rear left 330mm

can you plz measure the seats? thanks

J

Will keep you posted Jaik, I shall get the guys to do these when they have a moment

Steve

w00t. I should also mention the Bride rails have one normal round hole (front right) and the rest are elongated at around 30mm, basically allowing the installation of a seat of approximately the width ive listed above.

JK

Also interested in a all-black set of seats for my R33.

Out of curiosity, do you have any seats currently in stock that are the same style as the black ones? I only ask as I wouldn't mind coming down to have a look first before going ahead with the purchase.

Thanks

Also interested in a all-black set of seats for my R33.

Out of curiosity, do you have any seats currently in stock that are the same style as the black ones? I only ask as I wouldn't mind coming down to have a look first before going ahead with the purchase.

Thanks

Hi mate, we sure do. Feel free to drop by anytime and have a look

Regards,

Steve

about how much would it be to get the rails modified? very interested but jus abit worried about the installation cost haha. and would you guys do an install service?

The modifications to the universal rails to get them to fit your car, it's a simple welding job right? My mate is a welder who could do it for me for nothing if this is the case (he's a professional). Or is the mod something you need to get done by an approved workshop for safety reasons?

The modifications to the universal rails to get them to fit your car, it's a simple welding job right? My mate is a welder who could do it for me for nothing if this is the case (he's a professional). Or is the mod something you need to get done by an approved workshop for safety reasons?

Hi mate, thanks for your enquiry. The modifications required are generally minor depending on the car the seats are being installed in.

We recommend having them fitted by a knowledgable workshop or competant welder.

Cheers,

Steve

if they do bolt straight up to brise rails, how much can we purchase bride rails for?

We found that the genuine Bride rail needed a few minor changes before the seat could be bolted up as 1 or 2 of the holes didnt quite lineup and had to be redrilled on the rail itself to suit

Cheers,

Steve

Thanks JK, which email did you send it to?

Feel free to pm me

MSPEC: Confirming if we have a set of the black with grey centre in the showroom, will let you know shortly.

Thanks

Steve




  • Similar Content

  • Latest Posts

    • I used to have Walbro 255's when they were a pretty common update. (or were they 044? 040?) In any case I had a dirty tank. I thought the tank was good, but I would find the filter would clog in maybe ~50km of driving. If the issue persists, well, your fuel system or tank has crap in it that the pump is sucking up.
    • Hi. Ok thanks for the info. I/we do not know what tune is on that Nistune ECU so it is why there is stock ECU and that Nistune is for later when the car is done. I have guy who tunes Nistune and other ECU so i will then take it to him to see and properly tune for the car   And for the update. On 99,9% it is bad fuel pump. Which is wierd cuz it is like 2 years old(brand new walbro 255) and that filter (also brand new) was dirty.  I was alwaya pumped premium(100) on very good petrol station so i dont know how is that possible...  
    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
×
×
  • Create New...