Jump to content
SAU Community

Recommended Posts

Ive got to go overseas for work in the next few weeks several times, and was wondering if anyone could tell me a safe period of time i can leave the car without haveing to get someone to start it and/or drive it?

I will disconnect the battery, but was just a little concerned about seels or gaskets drying out / seizeing.

So does anyone have an opinion on how long they would leave a car sitting in the garage without turning it over, or am i being a little cautious.

Cheers fellas.

Not that it will make a difference, but the car is a R32 GTR and the time frames im looking at range from 2-3 weeks to 3-4 months.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/86702-how-long-to-leave-car-sitting/
Share on other sites

don't worry about it, your car probably spent 3 months without being started before it got to Aus. The battery would be the only real issue.

Just give it some new oil when you get back and off you go :D

just watch for those gremlins.... i had my car off the road for 3 months .. and she was having issues with stalling.. took the car off the road for 4 months and then it wouldn't idle ever again...

just about to get it back on the road again after 9 months .. hope it doesn't get any worse.......

normally it shouldn't be a n issue.. mine just freaked out on me LOL

I would add some obvious things. Don't have a full tank of fuel because it will eventually 'go off' so try and have as little as possible (but not completely empty = bad for fuel pump).

Do as Duncan suggested and replace the engine oil at the very least. I would probably change the oil filter and fuel filter too.

When you come to starting it again. don't try and crank it very first go: let it build some fuel/oil pressure. Its good if you can get someone to turn it over every couple of weeks but I really wouldn't worry too much.

I had my car off the road for 2 weeks, it was little hard to start cause of the battery (cranked longer than usual had to try twice), it also had a bad missfire for the first minute or so but i just let it idle for a while and it was back to normal. I guess it would have been cause of the fuel needed to build up pressure through the lines.But yeah, do disconnect your batt before you go, change the oil and fuel and CHECK YOUR TYRE PRESSURES when you do come back!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...