Jump to content
SAU Community

Recommended Posts

The R34 GTT ECU and TCU are contained in the one unit.

I have had my transmission rebuilt and I'm told it can handle 300rwkw without needing the soft landing, ie timing drop, that the stock ECU does.

I was reading Sydneykid's thread on the SITC and thought perhaps I need a piggyback ECU that goes between the stock ECU and the coils.

Which ones do this? Unichip?

Then I had a brain wave.

What if I get a PFC and plug most of the wires into it so it can run the engine. Then run extensions to the signal wires that the TCU requires to run the auto transmission over to the stock ECU so that both the PFC and the stock ECU will be receiving input from all the sensors.

Any wires that are sending information from the stock ECU to the engine will not be connected. The wires that send information the transmsission would be connected.

What do you all think?

Link to comment
https://www.sau.com.au/forums/topic/86992-powerfc-in-auto-r34-gtt/
Share on other sites

adam, the pfc will run an auto car. The only problem is flaring on the shifts as it doesn't pull back timing for the shifts.

I can't see your theory working but I am waiting to be proved wrong. :)

Why can't you just wait for darkhalf's boards? hehe

Edited by ed

I did think there shouldn't be any clear reason with enough wiring to run both ECU's simultaneously it shouldn't work??

I haven't seen any previous mention of this on here..

http://www.powertraincontrolsolutions.com/content-4.html

Any reason why?? other than the ~$1000 pricetag of course. I guess for R34 they have a slightly different version of the autos.

adam, the pfc will run an auto car. The only problem is flaring on the shifts as it doesn't pull back timing for the shifts.

I can't see your theory working but I am waiting to be proved wrong.  :)

Why can't you just wait for darkhalf's boards? hehe

The shifts wont flare on my car because my gears changes are too tight.

I know there is the odd R33 with PFC but don't R33's have a separate controller for the auto? What happens if I press the button on my steering wheel with a PFC and nothing else? Probably nothing cos it wont be connected to anything.

  • 9 years later...

Adaptronic 440. It has a lot of integrated features which can save you money, ie boost control, serial input for a wideband, programmable outputs, plus some neat adaptive tuning features, ie with a wideband it can automatically alter a fuel map (though best results are done manually). Plus theres a flex fuel functionality if you're interested in e85.

Just be mindful that you're starting from scratch with ignition and fuel maps, so the learning curve is very steep. Although there are base maps available, they arent very good. You'll need to learn how to tune yourself, even in conjunction with a tuner.

i was looking at other options to have a true 4" intake without going down to 3" for the z32, or not having to run a z32 in the cooler piping thats all

Nistune is not limited to running Z32 AFM. You can install an R35 AFM sensor into a 1000mm drainpipe if you want and set Nistune up to run with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...