Jump to content
SAU Community

Recommended Posts

Haha yeah it was the best looking but not the best to drive , the ceff felt better on the track and soon enough i'll make it look pretty again (just finishing a couple cars that i'm building that don't belong on this forum)

edit: oops , prev. page is what i was dribbling about :)

post-20231-0-86417700-1319265584_thumb.jpg

Edited by toffy

post some more pics up then! :)

Really like Stangs ceff, nice daily spec.

Get hassled by the boys in blue much?

Thanks. :) Haven't been pulled up as yet, touch wood, but probably just a matter of time. With the car all white it doesn't stand out like it used to with the black bonnet though.

Here's a comparison of how the rear of the Ceffy looked when I first bought it, and after the respray a couple of months ago.

IMG_0671.jpg

6253536651_25452a2d77_b.jpg

Remove those door bumpers like I did. You won't regret it.

Your paint is in good enough condition to pull it off without a noticeable difference.

Actually on that note, even on my horrible f**ked up paint, it isn't noticeable unless I point it out, or sometimes when it's dirty.

I did mention that to the panel beater who resprayed some bits for me, it's one of the few exterior details that still bothers me. Was mostly worried about having an obvious whiter line where the strip used to be.

Right rear door is actually a little yellower than the front, so may give that a going over again anyway though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...