Jump to content
SAU Community

Recommended Posts

i was just after some advice on installing a new hybrid GT Spec on to an r33 series II and have come in to a bit of a dilemma. i have the original piping and on the top pipe there is a little hose attached but there is no spot for it on the new piping. eg the pictures that i have attached. some advice would be much appreiciated.

thanks

post-12252-1126311494.jpg

post-12252-1126311670.jpg

Link to comment
https://www.sau.com.au/forums/topic/87186-fmic-install-issues/
Share on other sites

i was just after some advice on installing a new hybrid GT Spec on to an r33 series II and have come in to a bit of a dilemma. i have the original piping and on the top pipe there is a little hose attached but there is no spot for it on the new piping. eg the pictures that i have attached. some advice would be much appreiciated.

thanks

Whoa, resize those pictures *headache*

In answer to your question, the hose is for your boost solenoid. All you need to do is find another vacuum hose somewhere (I used the one that goes to the stock bypass valve) cut it and whack in a T piece, then run it back to the solenoid.

or you could drill a hole in the new pipe. whatever you do just make sure you tap into the pressure side of the piping otherwise the waste gate will not open and will over boost.

Other than that, how was installing the kit yourself and how long has it taken. I am looking at getting the same kit soon as summer is coming fast. Can i ask where you brought it from too?

or you could drill a hole in the new pipe. whatever you do just make sure you tap into the pressure side of the piping otherwise the waste gate will not open and will over boost.

Other than that, how was installing the kit yourself and how long has it taken.  I am looking at getting the same kit soon as summer is coming fast.  Can i ask where you brought it from too?

got if from flyn performance in sydney. bought it on ebay. delivered to melbourne $689 including freight and insurance. so far it has taken me a couple of hours

Whoa, resize those pictures *headache*

In answer to your question, the hose is for your boost solenoid. All you need to do is find another vacuum hose somewhere (I used the one that goes to the stock bypass valve) cut it and whack in a T piece, then run it back to the solenoid.

could you post up a picture mate that would be real helpful

sorry mate i have i am not sure, whats it look like?

That's ok. From the pipe that you swapped over, it connects to a cast metal pipe that then connects to the throttle body, then intake manifold. On the cast metal pipe right after your replaced pipe there is a 90 degree bend before it goes across the top of the engine, just after the bend there is a valve on the back side of the pipe. This is the bypass valve, and it should have a pipe of about 1 inch diameter going all the way back to before your turbo. The valve has a small black vacuum hose going to it, which is what you need to T into.

See how you go and let me know if you're still having trouble.

thanks for your help mate. i nearly had the wrong pipe there for a minute. so just to make sure the small pipe going off the stock bov. thanks for your help again mate, absolute lifesaver.

Yes that's right the small hose. Hope it all goes well! Make sure you have all the bits you need before you cut it.

i guys, i have hooked up my I/C as the same as in the pics above. i have a turbosmart bleed valve, but for some reason the boost wont raise above 9psi. does anyone know whats the go?

There is no vacuum at the original location only positive pressure I have the same kit and screwed a nipple into the new piping. You can T it into somewhere where there is vacuum hose (eg of the inlet manifold) but I suggest you put a one way valve in as well so your actuator doesn’t get effected the negative pressure and wear over time.

There is no vacuum at the original location only positive pressure I have the same kit and screwed a nipple into the new piping. You can T it into somewhere where there is vacuum hose (eg of the inlet manifold) but I suggest you put a one way valve in as well so your actuator doesn’t get effected the negative pressure and wear over time.

reckon you could post up some pics

There is no vacuum at the original location only positive pressure I have the same kit and screwed a nipple into the new piping. You can T it into somewhere where there is vacuum hose (eg of the inlet manifold) but I suggest you put a one way valve in as well so your actuator doesn’t get effected the negative pressure and wear over time.

Sorry, but that aint correct .. there definatley IS vacuum at the original location. What makes you think there isn't?

Sorry, but that aint correct .. there definatley IS vacuum at the original location. What makes you think there isn't?

Hook your boost gauge up to the original location and there will not be vacuum. Mine was T'ed into one of the hoses comming off the inlet manifold I had my car tuned at ICE performance Nigal told me to use a one way valve if I was to keep it in this location.

I will post pics tonight ICER33

cheers

Hey guys, I also bought the same kit from flyn, i got it a while ago & will be fitting it myself, but just haven't had a chance too, but it is sorted for next Tuesday when I will have everything I need.

Anyway, included in the kit I have is a 4ft long hose with a t-piece already in it, it should have come in yours too. I haven't looked tonight (only just recalled this thread now it's too dark to look), but judging from what you said earlier about the solenoid etc, this should be what it's for. I am guessing you can use this to replace one of the lines, as it has 2 outlets. I don't have a digital camera so I can't take a photo of it, but it did come in the kit & I would say that's what it's for.

For anyone else, if I can get hold of a camera for Tuesday I am going to take step-by-step pics of what I do for the fmic install, I'm sure the mods could make that a sticky & it will at least give a guideline of what do do if you are willing to get hands on with your car. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...