Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

i dont have dyno info,

but dont put on a pod without a heat shield, you will definately lose power if its judt ditting there in the hot engine bay.

stock airbox with panel filter and cold air pickup pipe is usually the most effective value for money

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-1576497
Share on other sites

  • 1 year later...
is there a difference b/n the gtst and the gtr stock box? in the r33 especially.

no. I run over 250rwkw.

Wack in a hi-flow panel filter and u will be set. I was convinced that unless u have a sealed box...ur just wasting time. Mine was loud and annoying...also a cop magent...stock box is quiet...and stealth.

I use a Trust Panel filter...works a treat. Dunno how much they cost but a K&N would also be fine.

Although I'm designing a new snorkel for the stock box...we be finished in a few weeks...will post pics. But its runnign fine as is right now.

KJ

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820094
Share on other sites

Hi there,

I did it on the dyno and absolutely NO difference. 254 rwkw power runs - stock airbox with K&N flat panel filter one run, then we removed the top of the airbox and flat panel filter so NO RESTRICTION WHATSOEVER and the same 254 rwkw power output - both runs done with the BONNET UP so no temp differences either.

The turbo is 2835pros kit so has fabricated aluminium turbo intake pipe which mates up with the stock airbox.

Around these power levels pods are a waste of time/money unless you like to hear the turbo/blow off valve - and in a lot of cases poeple will see a decrease in power due to the engine sucking hotter air.

Cheers

Edited by gtst25
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820218
Share on other sites

it would be ok having the pod sitting behind the front bar low to the ground? thats what i got and it's barely even dirty after 1 year, then again i never travel on dirt/gravel/sand roads, the only thing i do is avoid puddles or where theres to much water build up on the road. Sometimes the sounds gets very annoying and I wish i still had my airbox

Edited by Hulk1010
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820279
Share on other sites

it would be even better having the open top type filters sticking low and just behind one of your front bar slots. In a S2 R33 with front bar (stock) after doing FMIC it is possible.

people have had issues with direct mount pods like this...too much air at higher speeds. They needed to baffel it to stop issues at 80+ kmph.

That being said..the gain ur gonna get..hmm not too much...stick with stock, get a decent filter, protect ur engine from crap and avoid another defect, oh an piss of they stupid whoosh sound..lol.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820493
Share on other sites

thats good to hear. especially as i've just ordered a apexi panel through kudos motorsports:P .

always wondered if its possible to do a CAI on the stock box. is this what your trying to achieve chris? any one else done this? pics would indeed be helpful :no:

andz 69: i guess it dependes on how much power they're running (which i havent a clue about). we are talking performance benefits at power levels of bout 200-300kws though

Edited by Basti
Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820527
Share on other sites

I pulled off the pods and got a hold of an airbox and k&n filter simply because,

it's my daily driver (don't want to risk defect),

Pods are illegal in NSW and can't be engineered unless fully enclosed(too much stuffing around),

heatsoak in traffic.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820530
Share on other sites

personally I'm not convinced of the pod style installs where they just sit in the bay. I have done this to a few cars an recently just returned them to stock which better filters and intake pipes.

As long as an air filter and box is properly sized for an application, the lost airflow will be very minimal. I haves een some1 do actual testing but cant find the link.

If ur worried build a new lid for ur stock box and feed more air into it with a new snorkel...looks stock. In fact thats what I'm doing.

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820576
Share on other sites

My 2 cents

1. Air Box fanboy here....just look at the mines GTR

2. Pods are really only useful IMO when there isnt room for an airbox or it isnt suitable for plumbing.

3. I fail to see how a pod on a intercooled car will effect the inlet temps inside the cylinders....maybe a poofteenth of a degree once its passed through the intercooler? I can understand sucking in 15 degree air compared to 50 degree air will differentiate as the intercooler can only do so much in the amount of time it has an air molecule going through it, but with the forward acceleration of the car colder air from infront of the car should go into the pod, and I doubt that a majority of the hot air from the engine bay will get into the pod as it will most likely go out the top of the engine bay and over your window / into your vents etc....

the air that actually hits parts of the motor etc will bounce proportionally to the parts it hits.....

Therefore I fail to see air that is being slammed into the front of a vehicle travelling at XXX km/h when it has little velocity before it hits the car will have less of a chance to get into your air intake than the air that is rushing to the back of your engine bay and out of any gap it can find (as mentioned between ur bonnet etc)

my 2 cents of keyboard warrioring at 1.30am :no:

Link to comment
https://www.sau.com.au/forums/topic/87303-airbox-vs-pod/#findComment-2820622
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The obvious answer here is get a ND2/3 RF with the Targa top. The red is nicer, too!
    • This is the only point I can access with any floor jack and my car is SUV height - What's the actual suggested alternative here? I have also driven up on blocks in the past, but lets say you have a problem and the car is on it's wheels already and can't be driven up/off anything? Not a huge fan of bits of wood being spat in random locations either (it hasn't happened, but what-ifs occur) Perhaps I would also really enjoy having a quickjack :p Time to google quickjacks.
    • The wires look to be a healthy gauge, more than I would think the pump needs. I guess another concern is if the FPCM will be happy with the extra current draw. I have heard they are a bit sensitive.
    • It will be fine. The real question is whether the existing wiring is fat enough for the current drawn by the bigger pump. The 342 is not that hungry, but it will be well worth pointing an IR pyrometer, or even better, a thermal camera, at the pump hat wiring when it is running, just to make sure. Or, you know, just touch it to see how hot it is.
    • Hi guys, Sorry to revive such an old post! The fuel pump in my M35 has finally given up, the car has been sitting for 3 years so I'm not surprised. I bought a Walbro GSS342 of Scotty some time ago, so I'll throw that one in. My question is, if my car has no performance mods at all, do I need really to mod the wiring to supply constant 12V? or will the new pump be just fine at the reduced voltage at idle? Thanks guys..
×
×
  • Create New...