Jump to content
SAU Community

Hi I Need Help On Where The Water Temp Sensor Rb25

HKSGT25

By HKSGT25,
in General Maintenance

 Share

Recommended Posts

HKSGT25 Newbie

HKSGT25

Posted
Posted

Hi I need pics or locations (pics would help alot) this is for Defi gauges, I have both oil temp and water temp defi gauges, I have a clue on where put the water temp sensor at, there's 2 plugs for the water temp, the left one has 2 wires but the fiting is too big for the sensor to screw right in, and the left one which is small and has 1 wire and might fit the sensor, and as for the oil temp gauge I have no clue on where to put that, people at the audio place say to drill a hole in the oil pan and install the sensor but i'm like "is there anyway besides drilling" isn't there a sensor for the oil temp to go on and replace with the defi sensor??? Thanks for reading guys and any info would help me out alot. pics would even help this problem out. thanks. this is for a RB25DET.

Craved Grand Master

Craved

Posted
Posted
Hi I need pics or locations (pics would help alot) this is for Defi gauges, I have both oil temp and water temp defi gauges, I have a clue on where put the water temp sensor at, there's 2 plugs for the water temp, the left one has 2 wires but the fiting is too big for the sensor to screw right in, and the left one which is small and has 1 wire and might fit the sensor, and as for the oil temp gauge I have no clue on where to put that, people at the audio place say to drill a hole in the oil pan and install the sensor but i'm like "is there anyway besides drilling" isn't there a sensor for the oil temp to go on and replace with the defi sensor???  Thanks for reading guys and any info would help me out alot. pics would even help this problem out.  thanks. this is for a RB25DET.

does it use a probe or just have wires to hook up the the std sensors?

probe ones for water temp use a connection in the pipe running to the radiator from the thermostat..

try to get a double adapter that you can use for the oil temp from the std location of the oil pressure sender.

SideWaysChef Collaborator

SideWaysChef

Posted
Posted

Let me know if you find anywere to locate a oil temp sender

I had the engine out of my car and couldnt find anywere to put it. About the best i can do is buy a sandwich plate for the oil filter and tap on into this

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...