Jump to content
SAU Community

Awesome Garrett/hks Gt Turbo Deals

BigDatto

By BigDatto,
in Engines & Forced Induction

 Share

Recommended Posts

BigDatto Proficient

BigDatto

Posted
  • Author
Posted

I enquired about the Free Trade Agreement with customs officers at Clyde, they clarified that it only applies to goods manufactured in the USA, & there has been some confusion over this point.

example A: goods mfg in USA, purchased from USA, no import duty

example B: goods mfg in Canada, purchased from USA, 15% import duty

example C: goods mfg in USA, purchased from Asia, 15% import duty

Also there are concessions for certain vehicle parts, but i didn't get the lowdown on that.

so... buyer beware !

Sydneykid Grand Master

Sydneykid

Posted
Posted (edited)
I enquired about the Free Trade Agreement with customs officers at Clyde, they clarified that it only applies to goods manufactured in the USA, & there has been some confusion over this point.

example A: goods mfg in USA, purchased from USA, no import duty

example B: goods mfg in Canada, purchased from USA, 15% import duty

example C: goods mfg in USA, purchased from Asia, 15% import duty

Also there are concessions for certain vehicle parts, but i didn't get the lowdown on that.

so... buyer beware !

Never had a parcel opened by Customs from the USA since January, if it is post marked "from the USA" they seem to let it through. If the value is high enough they slap some GST on it, but never had any duty applied.

The definitions of "made in", "manufactured in", "product of" etc are just as blurred as in Australia. I think it is just too hard for them.

:wub: cheers :wub:

Edited by Sydneykid
wrxhoon Grand Master

wrxhoon

Posted
Posted
I enquired about the Free Trade Agreement with customs officers at Clyde, they clarified that it only applies to goods manufactured in the USA, & there has been some confusion over this point.

example A: goods mfg in USA, purchased from USA, no import duty

example B: goods mfg in Canada, purchased from USA, 15% import duty

example C: goods mfg in USA, purchased from Asia, 15% import duty

Also there are concessions for certain vehicle parts, but i didn't get the lowdown on that.

so... buyer beware !

The 15% duty is long gone from anywhere , its now 10% from countries other than USA ( since jan 1-05 ) however bigdatto is correct but in practice what SK said goes , no-one will open a parcel from USA but dont forget the 10% GST is payable always .

BigDatto Proficient

BigDatto

Posted
  • Author
Posted

I only mentioned this because they did open the parcel (in front of me) & said "WTF is this ?? (to use the parlance of our times). If I had let the parcel continue to the post office I'm sure it would have remained sealed. But xmas had come early & I couldn't wait !!

2fast4u Newbie

2fast4u

Posted
Posted
Never had a parcel opened by Customs from the USA since January, if it is post marked "from the USA" they seem to let it through.  If the value is high enough they slap some GST on it, but never had any duty applied.

The definitions of "made in", "manufactured in", "product of" etc are just as blurred as in Australia.  I think it is just too hard for them.

;) cheers  :)

dude i got ripped off by custums they charged me more than my goods were worth, they had what i paid then put what they thought they were worth, WTF i got it shipped through UPS, which i thought weren't too good but who do you get your stuff through?

wrxhoon Grand Master

wrxhoon

Posted
Posted
not always...

You may not pay but its payable , regardless where you buy localy or o/s .

You must also pay gst on the cost of freight .

lwells Grand Master

lwells

Posted
Posted
link to his ebay account/username/goods listing would be much apprecited

Because I am a nice person:

http://search.ebay.com/_W0QQfgtpZ1QQfrppZ25QQsassZmybasquie

i think bigdatto has done that on pg 1,

i tried emailing the guy about the HKS TO4R but no response yet.

Yeah, I also emailed him an no response yet.

Angry Proficient

Angry

Posted
Posted

i got a response from him yesterday..... doesnt stock internal gated T3 turbos..... :D

but finding out about external stuff shortly.

i think he'll find he's way to this post shortly.. coz he ask where i found out about his details.

  • 3 weeks later...
lwells Grand Master

lwells

Posted
Posted
what about things bought from asia? what taxes apply there??

Depends on the item, but standard GST/import duties apply. This may change in the near future if the proposed free trade agreements with some of our Asian neighbours go ahead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...