Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Fuel cut defender is basically a device that sits on the signal from the AFM to the computer and stops the signal from saturating which would cause the boost cut to be hit. Boost cut on most Skylines is about 1.1bar, the fuel cut defender stops it from hitting boost cut, can be good if you have aftermarket turbo's.

I'm ignoring you Ken.

See'ya:burnout:

Natural progression items to mod ?

1. Exhaust, Cat back

2. Intake

3. Boost up (small)

4. Front Mount Intacoorla!

5. Exhaust, Dump and Front, and Cat.

6. Boost up more

At this point you can choose to start blowing intercooler pipes and working your turbo too hard like our buddy Hicks.

Or take the other A/M Turbo Approach, possibly bigger injectors and all the stuf that goes with it... this is when you start spending the BIG $$$ (something I'm not going to do)

-Kym.

Originally posted by Adrian_perth

strich9ine u big dawg

may i ask what mods you done to ur car?

to get that Fast and Furious Style 14.8?

adrian :D

http://www.hyperwa.com/sau/mycar.htm young adrian..

and the 14.8 isn't my fault it's running richer than your mum's pimp!

overfuelling BAD! safc coming soon.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...