Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

your stereo sounds great cam - what u got in there? usually its my car doing the vibrating thing haha but i havent got the settings right since the battery went flat and stuffed it up.

Big Poppa Just entered! :)

How r ya kids?

paul sorry missed your call yesterday i had my fone on silent while i was sleeping lol :O ahhhhhhhhhhhhhhhh i missed another cruise good one adrian your a absolute star :P so i figure you all had fun? nice work did you miss me? and paul why are u wearing a man utd shirt? and did u steal it from me coz i am missing mine lol who was that dude with the fast and furious graphics down the side of the car?

adrian ;)

yeah its a poster from a movie - i liked it thought it was funny - i'll change it back later. yes they are doing the nasty thing - actually shouls see the full size poster every position possible :)

paul, i swear next time i will come :P i bet my life on it :)

i knew you love spending time with me ;) lol anyways you should feel special that you have the same man utd shirt as me hahahaha too bad i don't support them ehee i'm a leeds boy! i'm at tafe hey i decided not to quit! no more bumming for me!

adrian :O

niz - 2 12" subs and a set of splits and two nice size amps... nothing on that lexus tho.. jeezus! but still enough to keep me happy.. new stereo toy is my 40gig mp3 player.. i don't even carry a cd case anymore! got nearly 5000 songs at a good bitrate and still have 10gig left to play with...

did find a track on wanneroo rd that made my throat vibrate... kosheen has some wicked bass lines.. hehehe... :)

A blind man enters a lesbian bar by mistake.

He finds his way to a bar stool and orders a drink. After sitting

there for awhile, he yells to the bartender in a loud voice, "Hey bartender, you wanna hear a dumb blonde joke?"!!!

The bar immediately falls absolutely quiet.

In a very deep, husky voice, the woman next to him says, "Before you tell that joke, sir, I think it is just fair giving that you are blind, that you should know five things...

1 - The bartender is a blonde woman.

2 - The bouncer is a blonde woman.

3 - The woman sitting next to me is blonde and is a professional weightlifter.

4 - The lady to your right is a blonde and is a professional wrestler, and

5 - I'm a 6 foot tall, 200 lb. blonde woman with a PhD., a black belt in karate and a bad attitude!

Now think about it seriously, Mister. Do you still want to tell that joke?"

The blind man thinks for a second, shakes his head, and says; "Nah...not if I'm gonna have to explain it five times."

Hehe thought it was agood 1

Hoooray adrian u are writing correctly, well almost :)

hahaha boostzor! i have been trying my hardest not to puch that damn enter button so much! and you know what i think i am over it! damn straight!

paul, as i said i will be at the next one! i ain't avoidin you! unless i find out your gay? lol :)

anyways dudes i am out now off to the gym whore yas l8r on today!

adrian:p

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...