Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Kyles - Strip poker would be more interesting

Alex - hmm im scared to ask about the secret handshake - hopefully we are talking about shaking hands and not .... *niz shuts up*

Well ur in the same house - thats a start :)

Liz, I really do hope things work out,

Great idear, go over seas, have a break, clear your head.

From what i have heard he sounds like hes in the wrong. People should have friends of both sexes, as long as that its your partner that you go home to in the end, thats what counts.

Troys great, yeah he gets a bit gelous at times but he trusts me. I preve all the time.. and im open about it. I told him i had a good perve and some ambo while in hospital, If we go see a movie.. Ill jokingly say oh i can perve on so and so. Its life. Im sure troy perves on chicks too but i know im the one he wants and comes home to.

Hes just insecure because he knows how wonderful you are and how other guys would love to be in his shoes!

Thanks Kyles and Troy

niz - I just need to get away from all the influences here...parents, friends, his friends etc etc

I lied to him though about who I called when he asked me cause I knew he would chuck the shits - but I didn't know he had taken my phone and gone through it.... he's like "who are these guys"

Originally posted by SHUTO-BOY

hehe thanks Niz; yea the paper clasp,i got that idea from staring at my desk

?? im losing it

Yes u are ..... coming from a chick who calls her felt tip Pen Freddo :)

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...