Jump to content
SAU Community

Recommended Posts

http://www.prestigemotorsport.com.au/au/st...sp?StockID=1274

I hate how geoff risbey takes absolutely no responsibility.

but he's charging for the service of selecting a good car.

that line he uses about "additional inforation can be made available for interested buyers, but please be specific about what you would like to know" is horse shit. You pay him, he's supposed to tell you what you need to know to make an informed purchase.

stupid snapperhead!

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

my front bar has seen better days..... unfortunately after repetetive hits its starting to develop small fractures, so I need those fixed plus where I had the nismo badge ( which was recently lost ) that will need to be smoothed out , the rear needs to also be smoothed out where a hacksaw was used for the install of the FMIC and I would like a respray to get rid of all those nasty little white chips I have collected..

im pretty lucky cos i dont have that many white chips :) the stones seem to hit the grill bit (where intercooler one day is too sit) .... and the bottom of the grill has become unstuck and needs to be reglued down.

i need to get the packaging tape sticky off where i went a bit over excited with it on the rear - looks like im going to have to replace that GTS25T badge on the back too :)

hehe dont even get me started on on my bent fins from stone chips!!!! :)

yeah its frustrating isnt it, having to spend quite a few dollars on the car and not really getting anything for it.... if you know what I mean... like after I get my car serviced and the bumper fixed , its going to look and drive like it did before but I am out of pocket alot.... just think of what that money could have done if spent on other mods :)

i know :) i know :) .... bloody 3K on tyres and suspension since i got it ...... another 1K on servicing :) ...... 4K that wouldve been FMIC and Zorst money with probably enough left over for an EBC ..... make me angry!

oh well not much of a choice haha ..... ive basically done all i can mechanically so i think it decided to chuck its wing off just to fustrate me :) .... my car is evil tell ya .... i think its a girl cos it can be a total bitch sometimes

Sorry Dan I have no idea on the cost for that???

Niz.... I hadent heard.... does that mean you have no brakes at all or are they just performing very badly????

Mine could probably get away with a good machine but I think I would rather have a good set of slotted DBA's.... brakes are something I want to have the best in....

it snapped completely thru but sat on the caliper in such a way the fluid didnt leak much and still go through ........ apparently im a vERY lucky girl. specially the way i tend to drive!!

haha try 170km lately been really nauti!! gotta straighten up or im going lose my license!!

yeah Alex i know - but i kinda someone that likes to have enough money cos for some reason things start to get complicated with my car .... e.g brake pades .... then next thing i know i need the lines replaced as well ....

Guest
This topic is now closed to further replies.



  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...