Jump to content
SAU Community

Recommended Posts

that was the first one?

First one i went ot was at Metros about three years ago and they decorated Metros up more .... bigger crowd ..... even opened up this outside bit i never knew existed put a tent up outside with heatlamps and cushions etc. haha Me n Mel were reminicing about the bus trip between Metros n Globe the first one we went to ... i was freaking out and all she can remember is sitting next to a pot smoking bundeburg rum bear haha funny.

And Belmont Park was the greatest of the lot!!

Never been to one a Belvoir tho.

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

haha it was quite ironic cos i was brought up religous and they used to hold big church assemblies at Belmont Park ........ 10 years later back at Belmont doing everything i was taught at church not do :P

haha yeah Aidwin was wathing this chick at Belmont who couldnt walk two of her guy friends had to carry her ...... and i went to Mel "NEVER let me get like that!" Some people just go to crazy and it goes from fun to dangerous.

next for paul is sitting on his arse whoring.

hehe Zombie Dan .... Melbourne Cup at Ascot was the funniest i have ever been like that ..... i drank so much too ..... thank god for sunglasses cos i bumped into so many people i knew that day and it took me about half an hour to recognise them :P

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...