Jump to content
SAU Community

Recommended Posts

Heheh yeh :D

The fwd ca-18s are almost impossible to find and even then u cant guarentee that it will be in any good condition and there is nothing worse than swaping the engine cause u can save 500 bucks then realising the new engine is almost as bad as the one u took out.

If i rebuild it at least i get a 12months guarentee and know thats its in good order. So its worth the extra in the end.

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

got bowfinger on video yeah its a funny one when your feeling brain dead - nah i watched gone in 60secs - yeah i know acting is crap storyline is crap but must admit its better storyline than FnF but oooh the cars

shaun: yeh fair enough. most wreckers give a xx month guarentee on their engines as well though... i went through this process when my engine fried and ended up goin for a 2nd hand engine cos theyre so cheap, and its lasted me since (apart from the screwdriver incident)

paul; there wont be any drifitng for a while, dont worry

Booster, Your right, the ca18 is an old engine, most transplant won't be in great condition.

Niz, He popped down to Wanneroo yesterday, so I had a quick chat with him. I think his Mrs gets pissed if he spends too much of his free time doing car stuff.

See'ya:burnout:

Niz,

I love the cars in both movies, I have them both on DVD, they can never be watched too often:D

Can't wait for FnF2, that will suck, but I love cars:D The acting can't be as bad as High Octance 2, those kiwi's piss me off.

See'ya:burnout:

Yeh alot of wreckers will give a warranty but no wreckers over here have the engine. i found 1 engine with a siezed turbo and it was a rwd. Even if i could get it in which is doubtfull (according to some sources) i would need a new computer or even remap the current ecu for around $500 which is more money again. I think ive done enuff research to come up with a good result form reasonable money.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...