Jump to content
SAU Community

Recommended Posts

make sure the globe is located in correctly

if it is not in the correct position

the spring lock will still catch making it look like it is in properly but

you will not get the same reflective performance

try switching globes left to right

may be a faulty globe also

i know for my lights (r33) there was 2 adjustable screws.. top one did nothing, bottom one moved it up and down :D

that said, im also lead to believe the drivers side light isnt as bright, due to other cars being on that side facing your car, less blinding i guess.

It's fairly easy to allign yer lights.

Get a big bit of card board (like a fridge box from the back of Harvey Norman or something) flaten it, and use a marker to draw an even + shape on it.

Park the car on level ground in front of a wall or someplace where you can hang the cardboard level and square. Multi level Concrete carparks are good. Use a tape measure to verify the heights are the same to the bottom of each headlight just incase it's not the lights that are out of whack eg tyre pressure or suspension.

Park the car one or two metres back from the cardboard and turn the lights on, you should immediately see if one light is higher.

Before you play with screw drivers, use a white paint pen to mark the current positions.

To adjust headlights on some cars you first need to loosen all of the retaining screws slightly, then changing the angle with the adjustment screws will have better results.

Edited by zx9john
So the passenger side is meant to be brighter?

On some skylines they are even...can anyone one verify?

Most people on the road just think that my lights are on high beam,

can imagine what it will be like when i get HID.

the HID's arent too bad... they are bright, but they still point down, so not to blind anyone.

if you've loosened the retaining screws and the adjustment screw still does nothing sounds like it's stripped it's thread.

You could try a ghetto mod but make sure you can get yer hands on a complete replacement 1st :O You need to dismantle it and find out exactly what is wrong.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...