Jump to content
SAU Community

Recommended Posts

I want to put a v.spec logo on the back of my '93 R32 v.spec.

My understanding is that only the '94 v.spec II R32 had a v.spec badge (sticker in fact), but mine is a v.spec I.

So I guess I have two questions:

1. Did the v.spec R32 have a badge/sticker/logo on the back or anywhere to identify it as v.spec?

2. Does anyone have either a good close up photo of the v.spec (or v.spec II) badge/logo from an R32 GT-R? Also the exact dimensions, size of letters would be great.

Or even better if there was an original v.spec logo, can it be bought aftermarket or from Nissan?

Also, my car is an N1... so same questions above for N1.. where there any identifying logos/stickers, etc?

hi, the r32 gtr vspec did have a bootlid sticker. quite difficult to get from nissan. they still do the vspec 2 stickers. and they still cost heaps from nissan japan. about 50 bucks. the vspec sticker for the 32 is larger than that of the 33 vspec. the n1 has no real identifier. other than the visual ie headlights, missing rear wiper, no abs, rear parcel shelf, no sound deadening, brembo brakes, zn on blue plate, missing radio buttons near harzard light switch etc it is very hard to tell an n1. if yours is the same n1 that i am thinking about, i almost bought it about 3 years ago from brisbane street machines. back then it was 50k! does it still have the 18" white enkei wheels?

hi, the r32 gtr vspec did have a bootlid sticker. quite difficult to get from nissan. they still do the vspec 2 stickers. and they still cost heaps from nissan japan. about 50 bucks. the vspec sticker for the 32 is larger than that of the 33 vspec. the n1 has no real identifier. other than the visual ie headlights, missing rear wiper, no abs, rear parcel shelf, no sound deadening, brembo brakes, zn on blue plate, missing radio buttons near harzard light switch etc it is very hard to tell an n1. if yours is the same n1 that i am thinking about, i almost bought it about 3 years ago from brisbane street machines. back then it was 50k! does it still have the 18" white enkei wheels?

post-1554-1127354920.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...