Jump to content
SAU Community

Recommended Posts

hey folks,

On a bit of a highway trip a week or two ago, abour 40 minutes into it i realised that i was holding about 30-60 degrees to the right to keep the car straight, sure enough just as i realised the warning light came on. kept goin for another ten or fifteen problems then pulled over. after turning the car off and on it came good. does anyone know wat could have happend?

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/
Share on other sites

Don't take this the wrong way, but:

1. This has nothing to do with forced induction.

2. SEARCH. Yes, it sounds like a cliche but HICAS issues have been covered extensively. For some useful threads: http://www.skylinesaustralia.com/forums/in...icas+%2Bproblem

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1616246
Share on other sites

Now theres a good question.

HICAS is designed to turn the rear wheels slightly when you least expect it, throwing you off the race track.

But maybe a better explaination is that it is the active rear wheel steering on skylines and some other nissans. And over the last 15 years plenty of people have started having trouble with it, most often when they have installed an aftermarket steering wheel

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1618246
Share on other sites

that would be the crooked steering boss problem, the steering wheel sensor is not straight and after 10min or so without turning HICAS gives an error since it figures you can't have been driving in circles for 10min

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1618301
Share on other sites

exactly like that....loosen off the steering wheel, drive in a straight line for say 20m, then put the wheel on as straight as you can. drive another 20m to make sure you got it right then bolt it in place.

Of course if you have the wrong boss kit for your car that wont help :)

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1618322
Share on other sites

since the hubs are designed to turn when HICAS does, if you just remove the rack there is nothing stopping the wheels turning on their own.

So you need a HICAS lock bar, GTRGeoff on these forums sells them cheap :)

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1622544
Share on other sites

that would be the crooked steering boss problem, the steering wheel sensor is not straight and after 10min or so without turning HICAS gives an error since it figures you can't have been driving in circles for 10min

hi all

I have the same problem with my r32 gtr 10minutes driving on the expressway (no sharp turning) and the hicas warning comes on.

I have what appears to be the original wheel with the boss as part of the wheel so it cant be put on wrong position. there is a drive dog that locates the horn ring and steering angle sensor at the bottom and a 3pin socket for the horn wiring that locates at the top of the wheel so both are aligned vertical. there is a factory looking centre punch mark on the end of the steering shaft that lines up with the same mark on the wheel BUT on inspection of the zero degrees slot in the sensor disk it is about 160 deg right of the sensor. it all looks factory but either the wheel or the sensor must be from another model. Any help on how to id the right parts.

the wheel is 3 spoke leather bound with leather gtr horn button about 50mm dia.

Thanx

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1623593
Share on other sites

this might be a dumb question but how do u know if hicas is still working? i dunno if i have the bar, wat do i look for?

Yo Mass .... check this thread ..

http://www.skylinesaustralia.com/forums/in...showtopic=58778

This is from the Tutorail section..

shows the procedure for adding the bar.... so you can see what the hicas and bar look like ..

Cheers

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1623605
Share on other sites

My Hicas light comes on aswell like what Duncan was saying about after a while on the highway..

I have stock steering wheel - but for some reason when you line up the car to go straight the steering wheel is about 5-10 deg off being straight. SHould I take wheel off and rotate?? Is it possible with the stock wheel?

Or should I be getting a wheel alignemnt.

A mechanic thought I needed a new sensor - but the wheel is definately off centre so maybe should fix that first??

Link to comment
https://www.sau.com.au/forums/topic/89591-hicas-gone-mad/#findComment-1639990
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...