Jump to content
SAU Community

Recommended Posts

Hi,

Does anyone know how much gas and lubricant the A/C system takes in an R32 GTR?

I need to regass mine as there was no gas to start off with and it will be using the old gas (not R134-a).

The guy needs to know how much of the gas and lube to put in.

Got a figure of 500ml searching past forums.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/
Share on other sites

pretty sure i saw a sticker on one saying around 650g of gas.. normal oil charge is written on the label on the compressor, not the easiest thing to read while still fitted in the car. probably around 100- 120ml of oil at a guess.

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1622349
Share on other sites

Good thread, I recently had my a/c regassed as the condensor was removed.

Initially the thing would lock up and almost stall the car. :P

Brought it back, lots of water in it, they regassed it now it works on and off and is no where near as icy cold it used to be.

Unsure exactly what they have done or haven't done. :P

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1624286
Share on other sites

Best of luck with the re-gas and hopefully no problems arise.

They have just bought in a heap of new qualifications for the A/C people to try and adhere too. All gas has got to be accounted for - tight regulations and you will get screwed pretty bad if you dont comply.

Cheers

Sumo

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1625579
Share on other sites

I had my air-con regassed at the local mech as they were doing regassing cheap. The air-con would only work for 1-2 mins properly before blowing more hot air. I took it into the local Nissan dealer and they discovered that it had been over-gassed causing the system to everheat. i paid them $90 and they regassed the thing properly. it's as cold as ice now...........well almost :P

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1626015
Share on other sites

i just got mine regassed a week ago, guy showed me there was barely any gas in there, regassed it now works fine, only thing is the clutch makes a clunk noise when u turn the a/c on for the first time in a few days, the guy said it was fine they sometimes do that, does anyone else have this happen?

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1626168
Share on other sites

I need to regass mine as there was no gas to start off with and it will be using the old gas (not R134-a).

That sounds super illegal... and really bad for the hole in the ozone layer

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1627343
Share on other sites

stuff that was running r12 can be regassed with r12 if the leak is fixed, and the only problem with regassing with r12 is trying to find it, plus the cost. Its cheaper to convert it.

Its manly for the ppl in the industry that have bottles left over. Can sell it for over $60 a kilo

Edited by race_snooze
Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1629591
Share on other sites

Gees i bet the government wants to know who is still selling R12 a/c refrigerant. as it was phased out in 1996, and is pretty much illeagal to use/sell in this and just about every country in the world.

there was a gas made up when they phased R12 out, but it was only used for a few years as a substitute untill R134a was standard.

R12 is an ozone depleting gas. So if you want this planet to be around for your future generations i would suggest doing the right thing and convert the system to R134a

+ i would report whoever told you they could get you R12 becuase they are dodgy and i wouldn't trust them with my car anyway!

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1632690
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...