Jump to content
SAU Community

Recommended Posts

Hi,

Does anyone know how much gas and lubricant the A/C system takes in an R32 GTR?

I need to regass mine as there was no gas to start off with and it will be using the old gas (not R134-a).

The guy needs to know how much of the gas and lube to put in.

Got a figure of 500ml searching past forums.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/
Share on other sites

pretty sure i saw a sticker on one saying around 650g of gas.. normal oil charge is written on the label on the compressor, not the easiest thing to read while still fitted in the car. probably around 100- 120ml of oil at a guess.

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1622349
Share on other sites

Good thread, I recently had my a/c regassed as the condensor was removed.

Initially the thing would lock up and almost stall the car. :P

Brought it back, lots of water in it, they regassed it now it works on and off and is no where near as icy cold it used to be.

Unsure exactly what they have done or haven't done. :P

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1624286
Share on other sites

Best of luck with the re-gas and hopefully no problems arise.

They have just bought in a heap of new qualifications for the A/C people to try and adhere too. All gas has got to be accounted for - tight regulations and you will get screwed pretty bad if you dont comply.

Cheers

Sumo

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1625579
Share on other sites

I had my air-con regassed at the local mech as they were doing regassing cheap. The air-con would only work for 1-2 mins properly before blowing more hot air. I took it into the local Nissan dealer and they discovered that it had been over-gassed causing the system to everheat. i paid them $90 and they regassed the thing properly. it's as cold as ice now...........well almost :P

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1626015
Share on other sites

i just got mine regassed a week ago, guy showed me there was barely any gas in there, regassed it now works fine, only thing is the clutch makes a clunk noise when u turn the a/c on for the first time in a few days, the guy said it was fine they sometimes do that, does anyone else have this happen?

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1626168
Share on other sites

I need to regass mine as there was no gas to start off with and it will be using the old gas (not R134-a).

That sounds super illegal... and really bad for the hole in the ozone layer

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1627343
Share on other sites

stuff that was running r12 can be regassed with r12 if the leak is fixed, and the only problem with regassing with r12 is trying to find it, plus the cost. Its cheaper to convert it.

Its manly for the ppl in the industry that have bottles left over. Can sell it for over $60 a kilo

Edited by race_snooze
Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1629591
Share on other sites

Gees i bet the government wants to know who is still selling R12 a/c refrigerant. as it was phased out in 1996, and is pretty much illeagal to use/sell in this and just about every country in the world.

there was a gas made up when they phased R12 out, but it was only used for a few years as a substitute untill R134a was standard.

R12 is an ozone depleting gas. So if you want this planet to be around for your future generations i would suggest doing the right thing and convert the system to R134a

+ i would report whoever told you they could get you R12 becuase they are dodgy and i wouldn't trust them with my car anyway!

Link to comment
https://www.sau.com.au/forums/topic/89745-regassing-aircon/#findComment-1632690
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...