Jump to content
SAU Community

Please Answer Compatibility Question !


zulu
 Share

Recommended Posts

Hey everyone.

I was wondering if a 2002 R34 GTS (rb25) turbo will swap onto a RB20 ( r32 ) I have searched and only came up with compatibility for the R33 rb25 turbo.

And to the best of my knowledge the rb5 turbo does have a steel wheel and will flow a bit better and produce a bit more power ?

Thanks in advance I have to make my mind up very soon or the turbo is gone.

Please respond asap thanks

Link to comment
Share on other sites

I was wondering if a 2002 R34 GTS (rb25) turbo will swap onto a RB20 ( r32 ) I have searched and only came up with compatibility for the R33 rb25 turbo.

And to the best of my knowledge the rb5 turbo does have a steel wheel and will flow a bit better and produce a bit more power ?

well its an RB25 turbo, so its not really much different.

They are not steel wheeled at all, they are all ceramic or int he case of the 34 one, different again possibly?

more searching will give a faster answer

Link to comment
Share on other sites

Will this turbo yeild some power gains ? I bought it from 150 $ USD with exhaust manifold and downpipe. The car had 40K on it. But the guys says no shaft play at all and no oil leaks.

Was the deal a good one ? Do i need the exhaust manifold or downpipe for any reason ? If I do not then I will not get him to ship it to me since it will weigh too much.

Btw you guys are really helpful !!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...