Jump to content
SAU Community

Recommended Posts

There has been a couple of threads on this in the last few weeks.

A leak down test is more informative than a compression test.

Also, it's more important that the compression is even than that it is a particular psi on a particular gaugue on a particular day with a particular battery level with whatever temperature the engine is.

All of those things affect the reading.

Thanks for your reply, i got the results in and the compression in each cyclinder is as follows: 90 75 90 75 90 90. The guys at the workshop reckon this is okay. But like you said its pretty even. So should this be a worry at all?

There has been a couple of threads on this in the last few weeks.

A leak down test is more informative than a compression test.

Also, it's more important that the compression is even than that it is a particular psi on a particular gaugue on a particular day with a particular battery level with whatever temperature the engine is.

All of those things affect the reading.

Thanks for your reply, i got the results in and the compression in each cyclinder is as follows: 90 75 90 75 90 90. The guys at the workshop reckon this is okay. But like you said its pretty even. So should this be a worry at all?

If the compression test was conducted properly (warm engine, wide open throttle when cranking) then those results are pretty poor and the engine is fairly worn out. I believe Nissan specifications say 130 - 170psi.

WHat do you mean by wide open throttle when cranking? This GTR also has a worn out clutch would that affect the reults at all?

If the compression test was conducted properly (warm engine, wide open throttle when cranking) then those results are pretty poor and the engine is fairly worn out. I believe Nissan specifications say 130 - 170psi.

Engine should be adequately warmed, fuel pump fuse taken out, throttle floored and crank engine until gauge doesn't move. 8 or so compression strokes.

from nissan manual

new 171psi

normal 160psi

limit 128psi

14psi max variance between cylinders.

I tested mine and got 175 175 175 165 170 173psi, 1992 GTR

It was higher than stock? Could it be from carbon in the cylinders increasing the compression ratio?

when i got mine tested 1990 GTR

i got 140 140 135 140 135 140

which is ok for one thats done 100k little low but even so...

and as far as i understand u dont wanna go below 130

i dont know the whole deal but those pressures dont sound good

good luck

RellikZephyr

I just had mine comp tested at Grey imports here in sydney. 190 highest and 180 lowest..maybe gauge was reading high? But still pretty even which is a good sign, nathan there said, no need for a leak down test, its pretty good.

after I rebuilt my gtst - which is practically the same so be quiet all you GTR owners - I had a reading of 120 140 130 160 80 120 when it was cold and a reading of 160 160 160 160 160 160 when it was warm.

This is how much of a difference it will make so get it checked when it is at operating temp.

I also have forged pistons so be quiet all you cast piston owners....lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...