Jump to content
SAU Community

Recommended Posts

As topic says, how can you identify a Neo turbocharger from the R34 GTT Neo, from a R33 GTSt turbocharger?

Ive got a top condition turbo sitting in front of me, meant to be off a R34 and therefore its a Neo turbo & actuator.

Actuator says 28 4 Z06A and ASN 79

Turbo says 45 V 2

back of turbo says 21 U

post-18854-1128658115.jpg

post-18854-1128658256.jpg

Link to comment
https://www.sau.com.au/forums/topic/90242-rb25-r34-gtt-neo-turbocharger/
Share on other sites

Had a lookover the turbo, getting a feel for its condition. Actually I reckon the turbo is in fantastic condition with harldy any shaftplay whatsoever. Got it from a forum member for a decent price, and was heaps easy to deal with.

The front turbine looks to be plastic, so thats what the Neo is, isnt it?

Hi yeah, the compressor wheels are supposedly nylon/plastic based and the R34 turbo's are the same as an R33 model (I think the series 2).

http://www.skylinesaustralia.com/forums/in...=84465&hl=nylon

and

See http://www.skylinesaustralia.com/forums/in...=87783&hl=nylon

The R34 turbo I had in my grubby hands a little while ago had a black nylon compressor wheel and the turbine housing had stamped OP6 in 2 places. The width of the turbine housing behind the first turbine housing to chra bolt located just after the T3 flange was 50mm.

I've attached a pic where to measure.

21U I am 80% sure that is a R33 turbine housing, that is slightly smaller than the R34 turbine housing I had.

Edited by Cubes

I heard that the R34 GTT turbo is slightly larger, has a plastic/nylon compressor wheel, and is a "wet" ball bearing design.

R33's apparently have a ceramic compressor wheel, and are not ball-bearing?

Feel free to correct me!

All are ball bearing, as all have ceramic turbines.

The R34 also having the 'plastic' compressor wheel.

I think the R33 SII also had a 'plastic' compressor wheel, unsure if it has the larger R34 turbine housing though.

Edited by Cubes
All are ball bearing, as all have ceramic turbines.

The R34 also having the 'plastic' compressor wheel.

I think the R33 SII also had a 'plastic' compressor wheel, unsure if it has the larger R34 turbine housing though.

i checked my old car's turbo, it was a 10/96 model r33 gtst and it definetly had a nylon compressor wheel.

It all looks the same, thanks for the different info guys, thats been extremely helpful. I'll check it over again tonight.

I'll measure it up to see if I get 50mm thickness, and Im sure it has got OP6 in a couple of places.

On one of those threads (for bass junky's sale of turbo) he's got 45V1, where as mine is stamped 45V2 and the pic from Jmac says 45V2 as well.

Hopefully what Ive got then IS the R34 Neo turbo. Just has a different stamp number on the actuator (large 28 rather than a large 29).

Brendan

JMAC - that turbo youve got there - definately off the R34 GTT? Thats what mine looks like. Ive got to measure it up tonight.

Boy this is hard to determine! (without taking the current turbo in the engine off!)

siksII,

What was stamped on the turbine housing? OP6?

Sorry cubes, i honestly dont remember is was about 2 years ago, and the only picture i can find with the turbo in it u can only see the intake side and its too far away to see any detail either :P

But i remember checking the intake blades they were definetly some type of plastic. just by looking u cant really tell but when u touch them u can tell.

my current r33 has stock turbo, but is an earlier model than my old one, this one is an early 96 model(still series 2), i can have a look at the exhaust housing on this one (if i can see it properly!!!) and tell u what it says if you want?

Edited by siksII

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...