Jump to content
SAU Community

Auction Sheet Translation

R32zilla
 Share

Recommended Posts

Paradizzle Grand Master

Paradizzle

Posted
Posted

damn theirs heapsa sh1t on that report, the 2 XX's on the boot and rear left qtr panel means they have been replaced (pretty sure). Try posting it in the japan section on these forums, those guys are very helpful!!

Cheers,

Mark.

funkymonkey Grand Master

funkymonkey

Posted
Posted

lol nice cover up job of the USS auction report :D

Here's a rough translation of the japanese bits on the report, the XX's on the diagram means replaced.

Rear of car has repair history

Radiator Support is Bent

Back panel and boot floor is bent

Frame has dent in it

Also has:

Lipped guards (to fit larger rims)

Aftermarket exhaust, air filter, Suspension, shocks, Sway bars, Cold Air Intake, Boost meter, Nismo cluster (hence why km's are questioned), Steering, Shift knob.

It also mentions that there's many more aftermarket parts, and its probably best off being inspected in person.

Just above the factory optional tick boxes someone's taken to it with MS paint (while blocking out the auction run number, vehicle VIN etc) and cleared it out, so there might be more to it.

Sounds like a sweetly modified GTR that's been hit pretty heavily and is good for parts.

funkymonkey Grand Master

funkymonkey

Posted
Posted

depends what you want the car for, if its a parts taking car, then you don't need to worry about bent frames.

If "the car was purchased before the laws changed" :D then its can be imported as a 15 year old car and the conditions of eligibility is up to the engineer that signs it off. There's no chance a car like that is coming in under SEVS.

Rezz Grand Master

Rezz

Posted
Posted

What a mess... the car and the auction sheet!

Can't remember what 'R' on auction sheets means, it's crashed or something? Anyways, theres quite a bit of damage right the way around, but on the good side it's got a fair few aftermarket bits stuck to it, multiple guages, suspension, aforementioned exhaust, induction pipe and some other stuff I can't read... can you get a bigger scan? Some, nay, most of the kanji is illegible.

funkymonkey Grand Master

funkymonkey

Posted
Posted

R means accident repair.

off the diagram this is possibly what its supposed to mean:

a3 = heavy scratches across broad area on the front

paint blemish on bonnet and front bumper

u3 = heavy dent in side sil

au2 = medium dent scratch in rear driver side guard

a1 and u1 = slight scratches

w2 = repainted

Guest

Guest

Posted
Posted
Just above the factory optional tick boxes someone's taken to it with MS paint (while blocking out the auction run number, vehicle VIN etc) and cleared it out, so there might be more to it.

A good chance is since some people are still buying "15 year old cars" and putting them up for sale saying they were bought before Feb 7th but was 4 weeks ago not 8 months, they have been caught out so they try to cover their tracks a bit better.

re2 Collaborator

re2

Posted
Posted

Shit don’t start me.

:D

I only hope, that, the ‘individuals’ who honestly get caught through dodgy broker / supplier work, will be protected, whilst those who are responsible for been 'too busy running a straight shooting company', will get the rectum ripped out of there 'successful company'.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Yea that’s why I said ima test them with multimeter and see the reads.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Only at idle. Isn’t a problem when rev it seems.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...