Jump to content
SAU Community

Recommended Posts

Ok here is the problem, i have no power above 2500 revs, it will go up to here fine then once it hits that point then it will just stop like it is not getting any pertol. When it is doing this problem it will idle at about 1500 - 2000 revs instead of 500 - 1000 revs. Now this does not happen every time i drive the car and there is no common pattern that makes it do it.

I have had the car services and the mechanics cleaned out the injectors, put a new fuel pump in, checked the fuel pump, changed spark plugs and a heap of other things and could not find anything that is making the problem.

The car is a r32 gts-t (rb20det) with a 3" exausht from turbo and a 5" tip, and a HKS pod filter. Any help would be great as it is making the car so hard to drive.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/
Share on other sites

The 5" tip is your problem - too much bling for a R32 GTSt.

Seriously, though, if you searched these forums you would have been able to uncover that fact that a dead or dying AFM (Air Flow Meter) will set the ECU into limp-home mode and will not permit the engine to rev at more than 2500.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1633914
Share on other sites

  ronald_r32 said:
my bad its only 4"

Hehe, in that case maybe you need it upgraded to 5" ;)

Seriously though, it's almost certainly an AFM problem. I've had a similar thing happen when I accidentally yoinked out my S-AFC awhile ago, which among other things, severs the signal wire from the AFM. I also recently have my AFM die a half-arsed death, which resulted in the car being unable to idle, although I could get above 2500rpm in that case by keeping the throttle open.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634188
Share on other sites

Why not just run an ecu diagnostic rather than playing guessing games to see what your problem is? That will give you a definative answer to if your car has a bung AFM. Idling problems can be caused by an excessive amount of things just to name a few dirty/in-op/incorrectly set AAC valve, incorrectly set idle via throttle plate, carbon buildup on throttle plate, AFM problems, air regulator and the list goes on....

Do a seach and that should fix your problem.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634265
Share on other sites

Second hand should be around $150 or less. Try Ebay, you might be lucky. If not then JustJap should have one and they deliver too. Test it before you go and buy one first, it could just be a bad connector or something. See if you can borrow a known working one from someone and hook it up.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634395
Share on other sites

Going to the mechanics tomorrow to have it hooked up to a diagnostics computer. Hopefully it is just a bad connector as this will take away money from my FMIC ;)

What would cause it to go into limp-home mode, as it doesnt always have the problem?

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634419
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
×
×
  • Create New...