Jump to content
SAU Community

Recommended Posts

hey guys battery was playing up but is new so i got a brand new alternator, i no the regulator is internal, put it in and checked with the multimeter and is putting out 17.6v on idle. this doesnt sound right, i thought 14.6v was normal. any advice will be greatly appreciated. thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/90777-alternator-charge-rate/
Share on other sites

17.6V is waaaay too high, assuming your meter is accurate. Anything in the region of 14 to 14.5V is normal. Most likely your regulator is stuffed, but best get things checked.

Edit: make sure all your connections are correct.

Edited by SteveL

meter is 100%, this made car blow black smoke really bad[ fuel] ive had no luck with this car for the 18 months ive owned it, had to do everything a number of times cause everything i get for it is wrong. might as well keep spending on it cause its nearly brand new now. thanks SteveL

It's your alternator regulator, get it replaced. You will start frying very expensive electronics before too long at 17V. I know someone who had around 17V in his old crappy Magna, and things started dying one at a time. Headlight bulbs, dash lights, dashboard, stereo head unit. The stereo was the last thing to go for some reason, and it was only then that he decided to see what might be wrong with the electrics! I guess he had his priorities right, who needs a working fuel gauge as long as you have music :P

the alternator is brand new(genuine nissan), only put it in and run it for 20 seconds. voltage regulator is internal. spoke to the electrician today and he said maybe faulty, or a fuseable link could be stuffed. ill have a bit of a play but if i cant find it ill get him to fix it. thanks for the reply JimX

jimx i doesnt neccesarly mean your reg is shot alts on new cars use a battery sense wire this tells the regulator the conditon of the batty pull the two pin plug off at the reg check with a test light check to see if it has battery sense at one of the pins if no then thats where i would start lookin try and find where that battery sense has gone

also check to see if you have warning light by putting the earth clip onto pos and probing the two pin plug you should get a dull glow if you check in side the car for a batt light being on do all this with the key on

cheers hope that helps

As per the nissan manual, voltages should be up around 14 something volts when cold then drop to 13 something volts once warm.

How much was the alternator from Nissan?

Its possible they supplied the incorrect one? Unsure if that would cause overcharging or not. :(

Edited by Cubes

paid $330 for the alternator. its fixed now. checked the plug and it had 12.2 pos on one side, 12.2 neg on the other. bridged them and the charge light came on. put the plug back on and started the car and is now charging at 14.2v. ill just keep an eye on it, thanks for the feed back guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...