Jump to content
SAU Community

Recommended Posts

Hey guys...

somereason my indicators have just stopped working.... fuse checked out ok.. and the hazard lights still work (if this is even relevant??) does anyone know which relay i am to look for? incase mine is buggered? any other likely problems?

Link to comment
https://www.sau.com.au/forums/topic/91515-r33-indicator-relay/
Share on other sites

thats an easy relay to find as my car is stripped,, its a black square relay to the left of round one, there side by side, they are located to the way way left of the steering wheel buy lower, you may have to take tha dash facia off and take the bottom section off from undet the steering wheel.

I can get a picture if u like

thats an easy relay to find as my car is stripped,, its a black square relay to the left of round one, there side by side, they are located to the way way left of the steering wheel buy lower, you may have to take tha dash facia off and take the bottom section off from undet the steering wheel.

I can get a picture if u like

but my guess would be they the white plug at the back top of the dash section. Then you can put new globes in while its out, and chech the indicator globes, they are standard wedge globes.

Also it may sound strange but check the fuses under the bonnet

ok.... i found a page that said the indicator fuse was the one third from bottom and in left column in fuse box near drivers right leg. this fuse was fine. im convinced its the relay... checked fuses under bonnet and there doesnt seem many there. a couple of relays but if u say its near the steering column id be more inclined to believe that.

  • 14 years later...
  • 2 weeks later...

? Reallly?!?

 

...well where exactly? Lol. Had the main dash and steering surround off the other day and couldn't see any screws/clips at all to remove the lower trim.

 

Can only see one screw that can be seen in the pictures above, just below the left side of the speedo but that doesn't seem to loosen it at all. 

Edited by ossy

Even just

https://www.google.com.au/search?source=hp&ei=W5ALX5TvH4a1rQH-j6qYCA&q=r33+under+dash+screws&oq=r33+under+dash+screws&gs_lcp=CgZwc3ktYWIQAzoICAAQsQMQgwE6BQgAELEDOgIIADoGCAAQFhAeOggIABAWEAoQHjoFCCEQoAE6BAghEBU6BwghEAoQoAFQ1QVYgyZgjytoAHAAeACAAfABiAGWHJIBBjAuMTguM5gBAKABAaoBB2d3cy13aXo&sclient=psy-ab&ved=0ahUKEwjUiOKb48jqAhWGWisKHf6HCoMQ4dUDCAg&uact=5

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...