Jump to content
SAU Community

Recommended Posts

www.nengun.com is geat for turbo kits, If you tell us where you are located it will make it easier to give you advice on fitters!

Also there is a fair difference in what is required for 250kw compared to 350kw Can you narrow the range down a bit ie would you rather the high side or the low side of the range you stated??

Ok Nengun has several kits quite cheap. Id look at the HKS - GT-RS for the lower part of your range and the HKS - GT2835 Pro S for the higher part...as for fitters well I am from Brisbane so im no help there sorry

How about a pair of cams and a GCG High Flowed R34 GTT Turbo, or an RB25DET/VG30DET hybrid turbo High Flow.

SK is making 265 on an R34 GTT, and I'm about to have mine fitted and chase at least 250 rwkw.

You probably already know this, but anything over about 270 rwkw in a RWD is going to be $ on tyres!

The search function is your friend - use it :rolleyes:

There's a heap of info on this site that will help point you in the right direction. You just have to find it :)

In addition to the turbo kits mentioned above, perhaps also do some research on the GT3037, GT3071, GT3040R turbos. They'll all make between 250 - 330rwkw with the appropriate supporting mods.

www.gcg.com.au is worth a look as well ;)

How about a pair of cams and a GCG High Flowed R34 GTT Turbo, or an RB25DET/VG30DET hybrid turbo High Flow.

SK is making 265 on an R34 GTT, and I'm about to have mine fitted and chase at least 250 rwkw.

You probably already know this, but anything over about 270 rwkw in a RWD is going to be $ on tyres!

I was just wondering, i have a r34gtt & would be looking to make around the same power as that. Would you reccomend high flowing the standard turbo or aftermarket?? thanks :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...