Jump to content
SAU Community

Recommended Posts

Hey,

I got a RB20DET in a silvia.

Just drove my car seems to be alot of steam or clear smoke not white coming from what seems to be around the rocker covers.....what could this be does not show on the temp dial thats its overheating.

But is has caused the car to stall twice so far and it wont kick over until you leave it for 5 mins.

I need any help i can get ASAP.

- Thanks Luke

Edited by RB20DET_Silvia
Link to comment
https://www.sau.com.au/forums/topic/92620-urgent-help-please/
Share on other sites

I'd stop turning the engine over incase you're doing any more damage.

Does it smell like oil?

Do you have oil in your radiator? Do you have a full radiator?

I'd be looking for oil or a exhaust leak - depending on what it smells like.

Head gasket let go perhaps? did it occur after spirited driving?

The temp guage will read normal if there is no water in the system....it needs water to function correctly.

If you drove it till it stalled and did that a couple of times you will have warped the head. If may drive ok once the leak is fixed but get a leak down test done and find out how bad it really is. Another problem is that the turbo would have overheated severely also so there is a good chance that once you fix the problem, be it water pipe, welsh plug or head gasket, the turbo may have damage to the bearing which can cause them to fail soon afterwards.

Another problem that you will have to check is piston shrinkage. If it turns out to be a head gasket blown and you drove it until it stalled there is a good chance your piston can shrink in size once cool again. Make sure you get this checked out by whoever does the head work - BTW it will cost at least $600 to repair the head if it is warped.

have you found the exact point the fluid is coming out?

i had some trouble with my r33 dropping coolant but only after giving it heaps, never lost any thru normal driving. it was dripping down off the bottom of the block. traced the leak back to a tiny pin sized hole in a coolant line close to the block, guess that the leak was forced due to higher temps/extra pressure in the lines.

have since covered and clamped the hole (no more leaks even after hard driving), and am replacing the lines this weekend.

not sure if this is relative, but may be worth checking.

maybe a cracked block?

Look, engines run on smoke.  Once all the smoke gets out they are dead.

aaaahhh, i see you are wise in da ways of da smoke. applies equally to electrical systems particualry those installed in pommy cars and affiliated with lucas aka the prince of darkness.

You will be looking at a minimum of around $1000 to do a head gasket on one of these if you go through a workshop.

$1600-$1800 if the head is bent (which it more than likely is)

$4000 if the pistons have shrunk.

Good luck, let me know if you have any issues. I have dealt with many of these.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...