Jump to content
SAU Community

Recommended Posts

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

Link to comment
https://www.sau.com.au/forums/topic/93500-dissapointing-quarter-mile/
Share on other sites

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

is that a 6000 dump or u let it ride a little

is that a 6000 dump or u let it ride a little

i ride it a little. best way to explain would be that i let the clutch go in one fluid motion over a period of about a second or a bit less.

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

i have a feeling if i had 50hp less i would have done better time

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

what revs is rev limiter at

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

suspension does feel stiff, its tein not adjustable suspension, no camber kit

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

it's all about the first 60 foot. 2.5 is way too high to be able to run a low13/high12. i am pretty sure it's just a practice thing. and lower your pressures to about 24 psi. that will help a shiteload :(

Dump the 18's get some sticky street tyres on some 16's,select correct tyre pressures,change over your susp for some 90/10 's pedders,take the spare and any thing else loose out of the car,i would lightly slip the clutch on initial drop, short change into second,dont drive to limiter in 2nd then give it all you have got in 3rd and hang on,drop into 4th if you need it.The biggest mistake every one makes is using too much 1st and 2nd gear these only result in excessive wheelspin- hence your slow 60ft times,3rd gear is the one that does the driving and you must get up into it as soon as posible!

Anyhow good luck with your future racing (remember is not the out right hp but the way in which you hook up! )

Regards,

SKYLINE (Kym)... B)

Edited by skyline

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...