Jump to content
SAU Community

Recommended Posts

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

Link to comment
https://www.sau.com.au/forums/topic/93500-dissapointing-quarter-mile/
Share on other sites

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

is that a 6000 dump or u let it ride a little

is that a 6000 dump or u let it ride a little

i ride it a little. best way to explain would be that i let the clutch go in one fluid motion over a period of about a second or a bit less.

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

i have a feeling if i had 50hp less i would have done better time

i have 225rwkw and got a 13.5 at 109mph... 60 foot 2.3 on 235/45/17

then the next week went back (same set up) and managed 13.1 at 110mph

then went back and got 12.71 at 111mph 60 foot of 1.93 on the same tyres...

just go back and practice...

by the way i launch at 6 grand

hope that helps

what revs is rev limiter at

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

suspension does feel stiff, its tein not adjustable suspension, no camber kit

don't hit the limiter it will die in the ass before you grab the next gear... your MPH indicates a mid to high 12 sec pass if you can get the 60ft time down to 2 flat...

I suspect your suspension setup to be at fault... common errors for drag are too stiff a rear suspension and too much neg camber at the rear as the car has been lowered? modern IRS cars don't like to be lowered or you will just fry the insides of your tyres... which is even worse with wide tyres... get some camber adjustment bushes should help get the beast off the line

I went to dragstrip last night and managed dissapointing time of 13.8s, 109mph (175km/h)...car is r33 with bigger turbo (its T-57) making 347hp atw ON 15psi, and i expected at least low 13s...traction was shit 60 foot 2.478 sec, with shit trampio tyres at the back 18 inches 265 wide, tyre pressure at 40psi (stupid me checked today tyre pressure)...what do you reckon the car should do with this mph, and what launch methods u using, i managed best 60ft without much throttle at take off and whenever i upped the revs i couldnt do better time than 2.6 60foot...i noticed as well that gear stick was sticky on second run, i needed to push really hard few times to get it in third gear, still beat wrx hehe...what could the reason be? i suspect when car was brought here from japan while compliancing all the fluids have been changed except gearbox oil so it could be too old?

it's all about the first 60 foot. 2.5 is way too high to be able to run a low13/high12. i am pretty sure it's just a practice thing. and lower your pressures to about 24 psi. that will help a shiteload :(

Dump the 18's get some sticky street tyres on some 16's,select correct tyre pressures,change over your susp for some 90/10 's pedders,take the spare and any thing else loose out of the car,i would lightly slip the clutch on initial drop, short change into second,dont drive to limiter in 2nd then give it all you have got in 3rd and hang on,drop into 4th if you need it.The biggest mistake every one makes is using too much 1st and 2nd gear these only result in excessive wheelspin- hence your slow 60ft times,3rd gear is the one that does the driving and you must get up into it as soon as posible!

Anyhow good luck with your future racing (remember is not the out right hp but the way in which you hook up! )

Regards,

SKYLINE (Kym)... B)

Edited by skyline

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...