Jump to content
SAU Community

1996 Chaser Jzx 100 Tourer V Manual

sean01

By sean01,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

sean01 Enthusiast

sean01

Posted
Posted (edited)

1996 Toyota Chaser Tourer V MANUAL

Sydney

In Immaculate Condition Factory Dark Green

Purchasing New Car

$32000 ONO

VVTi 1JZ-GTE

59000KMs

4 Airbags

5 Speed R154 Box

Factory BodyKit (WALD Front Half Bar)

K&N Pod Filter

Oil Catch Can

Optima Battery

3 1/2" HKS Cat Back Exhaust

3" High Flow Cat

Earls Braided Brake Hoses (4 Wheels)

1 Week Old Rear TRD Diff Mounts

Factory LSD

TRD Lightened Flywheel

Brass Button Clutch

18" WORK Wheels

GAB Suspension

HID Headlights

BLITZ SBC- ID Boost Controller

HKS SS Blow Off Valve

DEFI Water & Oil Temp Gauges

HKS Turbo Timer

Nardi Steering Wheel (plus Original Airbag Wheel Supplied)

Contact me (sean) on 0416128193 for any further questions about the car

Edited by sean01
Link to comment
https://www.sau.com.au/forums/topic/94733-1996-chaser-jzx-100-tourer-v-manual/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 gtr transmission strength, billet plate

      By GTSBoy · Posted

      Just put skinny tyres on it.
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...