Jump to content
SAU Community

Recommended Posts

There is a street meet at AIR on this saturday is anyone going to go for a few runs. I am considering running just to see what i can do.

Does anyone know what time it starts, costs or any special things you need to do to your car.

Hopefully i will have some second hand Bridgestone 540s on GTR rims so i should have some traction.

Link to comment
https://www.sau.com.au/forums/topic/9476-street-drags-1st-feb/
Share on other sites

Clint,

I'm keen as mate! But due to family commitments (+ it'll be packed) I can't make it :) I probably won't be running for a mth or so :) Hope you get into the 12's!

Cost - $50

Starts - 4pm scrutineering 5pm racing

Need - ADR approved helmet, long sleeve shirt & pants.

Car - Registered & no obvious major faults (any major leaks etc..)

That's about it!

I'm guessing there'll be a HUGE turn out due to the first SM for mths! I'm not keen on huge delays due to heaps of cars, good for the spectators though (I won't even get to watch :)).

Originally posted by morpsi

Advertising it on Fresh FM at the moment. If I remember correctly, $15 to enter and $10 to watch. Gates open about 11am and racing starts at noon.

Dont quote me but tune into 92.7 for more details.

Cheers

Nat

Hmmm.... might have that radio dial just a fraction off 92.7 & didn't get the message 100% (j/k) :)

It's $50 to race & $17 for spectators ($12 concession)

yeah it dosent start till 4pm, this will give me plenty of time to get my car ready in the morning. Im taking off the rear wing, stripping out the seats, making a new exhaust (side pipe) and going to run avgas with some sticky tires im hopefully going to get tomorrow.

fingers crossed a mid 12 is the plan.

Geez Clint, it sounds like you are serious about this drag stuff!!!!!!!

12's should be a doodle, just might take a few go's

might be there to watch, if so i'll catch up with you:burnout:

Munro broke a driveshaft after the first pass i think.

I had 4 runs, but due to a diff that would only spin 1 wheel constantly traction was not there, best time was a 13.6 with unknown mph, but the run before was a 14.0 at 108.5mph so the best pass would heve been 110-111mph so that is definately good for mid 12s. it was my first ever meet so im not to disapointed, and went faster each time but when you have to take it easy off the line and still spin the wheels into 3rd its pretty hopeless. I was also told by a few people that the track was very slippery compared to normal. Keir wilsons GTR did a few passes but had a couple of dramas as well i think, he just smoked the wheels big time off the line as well.

My 60ft time was 2.35 so with a mechanical diff and some better tyres ( i was running nearly bald 540s tyres at 10psi in the end) i will hopefuly run the 12 next time. But at the moment after next weekend there is nothing planed as yet.

A 14.0 @ 108.5mph ( & fairly average 2.35 60) shows the cars potential! Pitty your 13.6 time slip didn't have a mph, would've been 110 @ least.

Lack of traction into 3rd :eek: sure does sound like it was slippery!

Bloody good effort for a first time out mate :uh-huh: Its one thing to have the power to run the #'s but it's a whole other ball game to get that power to the ground & run to full potential!

But hey isn't drag racing in a 5sp manual street tyre road car as easy as flooring the throttle & holding the wheel straight!?! *NOT*

Bummer about John's driveshaft failure :wave: Hopefully it's fixed & ready for next weekend?

yeah i was spewing when the 13.6 run didnt have the mph, i had to launch at about 3k otherwise i dint go anywhere when the turbo dosent make good boost to 4.2 its slow at first but hooks up in the top end.

with only one wheel spining all the time the burnout i got to redline it in 3rd and the car hardly moved, not like the normal sideways action you get.

i ended upjust getting some experience and will have to get the car setup to take the power and get the reaction toime down a bit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...