Jump to content
SAU Community

Recommended Posts

take out the spare wheel, rip out the plastic covering, fibreglass 1 sub in each corner of boot, make up a amp rack in the middle, done :D.

I have designs for a 12" side install sealed sub box too.

it can b done if u know what your doin, if any of u guys went 2 autosalon final battle 04 there was a silver r33 with full jl audio install 2x 12'' subs in the corners and 2 amps down the centre all fibreglassed and sprayed in r34 blue. this r33 is my own car and ill try get some pics up 4 u guys

why 1 sub per amp?

2 subs per amp better... lower impedance more crunk foe ya system...

use 2 x 2ohm subs (Assuming they are Dual Voice Coils), run your monoblock at 1ohm.. a good 1kw RMS of power... considering the monoblock does 1 ohm stable...

thats more power than 2 subs running off 2 amps

it can b done if u know what your doin, if any of u guys went 2 autosalon final battle 04 there was a silver r33 with full jl audio install 2x 12'' subs in the corners and 2 amps down the centre all fibreglassed and sprayed in r34 blue. this r33 is my own car and ill try get some pics up 4 u guys

Please do

it has a normal size one, like u would find in the engine bay of an commodore for example, also with rca'z what length is reccomended, i was thinking something about 12ft/4m is this right???

im running 4 gauge wiring into a distro block then thats going to each amp 1 monoblock and 1 4ch

system is 2 audiobahn 12z, kenwood 9152d monoblock, clarion 4ch, alpine type s splits for front and rear, and a pioneer audiovisual headunit

thanks

You can fit 'em in, but I would recomend to dump em for some 6.5 or whatever the factory size is as 6x9's are a good comprimise for getting bass without wanting a sub. You have 2 subs so I wouldn't worry about trying to fit 6x9's. If you do however you may need to bend/cut the parcel tray, which I definatley wouldn't recomend.

I'd runn 4g for each amp to a distro block, then 2 or 1g to the battery. Looks like you'll be getting some juice going into your system. Don't forget to fuse it correctly as close to the battery as possible.

ok, yeah ill prob go get a length of it and do that, as my amps are gonna be sitting on the sides of the boot

after spending a few hours working out measurements and all that stuff for my sub boxes, ive marked out everything in my boot, im gonna be making my sub boxes up next week as im going for my ps on monday so i wanna practice as much as possible

ill post pics up once the boot is carpeted

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
×
×
  • Create New...