Jump to content
SAU Community

Recommended Posts

hey Guys,

I have started cleaning up the wiring on my car and found the knock sensors weren't even hooked up. Now my car runs a Haltech ecu but i still would of thought it would need these to run, can anyone shed some light on this for me (esp where the sensor wire plud is suppose to connect to)

Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/
Share on other sites

Look down the back of the engine on the drivers side close to the inlet runners.

And on further searching have found that they do not incorporate closed loop knock sensor control.

Future reference....www.google.com.au

Type - Does Haltech use knock sensors

Google is your friend.

Edited by 3lit3 32
Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/#findComment-1729265
Share on other sites

Well maybe....

In the end if the tune is safe, you use good fuel all the time, your injectors are clean, your fuel pump is in good condition etc etc.

With skylines a standard ECU is the only computer that uses the knock sensor as input, it moves to a "safe" map when it detects knock.

PFC comes up with a knock "number" based on the sensor but does not use it in the tune. If it is knocking its up to the driver to back off.

AFAIK no other aftermarket computer uses an rb knock sensor

Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/#findComment-1730107
Share on other sites

  • 4 weeks later...
AFAIK no other aftermarket computer uses an rb knock sensor

The Link ECU has a system where if the knock is too high, it will reduce the boost level until the knock is reduced. The Link ECU uses the factory boost controller to control boost up to 14psi.. COuld be more, not sure though.

Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/#findComment-1799902
Share on other sites

bit of a question on this one...

assuming i'm using a stock ECU, is there any way to monitor knock?

I've got one of the Nissan Datascan units that Impakt (off these forums) makes that gives a readout of all the ECU parameters... the only one that it doesn't give that could be helpful is the knock readout....

any ideas?

Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/#findComment-1800147
Share on other sites

ok I have found turboXS make a knock light and shift light all in one ($180 approx) (look in the current autosalon mag) Unfortunatly every supplier for turboxs I have tried haven't even heard about them let alone stock them

Link to comment
https://www.sau.com.au/forums/topic/95529-knock-sensors/#findComment-1802668
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 🤔
    • If the gases flowing in those two tracts had the same properties, you could maybe use such broscience. But the exhaust has a different composition, different normal density, different actual density (because of different normal density, and mostly because of the massively higher temperature), and different viscosity (again because of much higher temperature). Consequently, all of the fluid dynamics parameters that matter, that you calculate from these inputs, such as the Reynolds number, friction factors (for wall friction) and so on, are all incomparable.
    • And we shall have to presume that Canada is the same?
    • In the US almost everything is E10. It can't exceed 10% by much or fuel systems have trouble adapting. At the same time because MTBE, MMT, and TEL are all banned they need as much ethanol in it as possible to boost octane.
    • I was mostly jesting. In my experience (and probably only my experience) the R34 GTT physical airbox space is actually too small to flow the amount of power it wanted. By sealing the box, I made it so it could only be fed by the ducts themselves. So you can seal it up and get nice cold air which IS good, but at a certain crossover point: More Hot Air > Less Cold Air I don't think you're at this point. In my case merely ducting the hot air intake with a very focused set of ducts counteracts the fact it's in a V8 engine bay. More cold air obviously best. The solution looks great.
×
×
  • Create New...