Jump to content
SAU Community

Recommended Posts

Hey all you sunny state skyline owners...

me and a mate went up there last weekend and stayed at my mates near bond uni and made a couple of trips down to surfers..... and damn i saw alot of skylines.... all tastefully modded.... no massive chromes or useless bodykits...... very very nice cars...

if you were driving through surfers last sat night i most likely saw u.... saw heaps of 32s... a blue one with black boot and wing... few more.... some really nice 33s (a couple with nice looking chicks driving them too!!!)

anyways keep it up and might post up see if someone will take us for a cruise next time we are up there... farken love surfers and that area in general... nice roads, lovely women, and the SUN!!! im still peeling from being burnt!!!!!!!

thanks

Ed (from nsw)

Link to comment
https://www.sau.com.au/forums/topic/97086-nice-job-you-lot/
Share on other sites

Really???? When where and how???

Maybe?

http://www.qldstreetcar.com/forum/index.php?showtopic=12673

Either way, someone isnt very impressed with him.

Keep it in the pants Mr Slide, or if it wasnt you, stop lending your car out. That member of that forum isnt particuary outspoken, so I highy doubt that is exgerated.

*please ignore all spelling mistakes, I just had to go change my gf's tyre as she didnt have all the tools in her car, and her spare was also flat, and its 2:20am*

Link to comment
https://www.sau.com.au/forums/topic/97086-nice-job-you-lot/#findComment-1762644
Share on other sites

Not really car just went up a gutter sideways and the origional repair to the chassis rail completely gave the left part of the shell is completely detatched from the chassis rail.

Everything else is fine.

but still it will never be the same.

Just shows how dodgey the origional repair was that was done to it so im actually now going to take it back.

I were not driving.

Edited by Slide
Link to comment
https://www.sau.com.au/forums/topic/97086-nice-job-you-lot/#findComment-1763143
Share on other sites

Maybe?

http://www.qldstreetcar.com/forum/index.php?showtopic=12673

Either way, someone isnt very impressed with him.

Keep it in the pants Mr Slide, or if it wasnt you, stop lending your car out.  That member of that forum isnt particuary outspoken, so I highy doubt that is exgerated.

*please ignore all spelling mistakes, I just had to go change my gf's tyre as she didnt have all the tools in her car, and her spare was also flat, and its 2:20am*

NO wasn't me in my car at the time, however i highly doubt that person driving would of even come close to another car considering i was in another car behind.

Link to comment
https://www.sau.com.au/forums/topic/97086-nice-job-you-lot/#findComment-1763233
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...